Assume frictionless flow in a long, horizontal conical pipe. The diameter is 2.54 cm at one end and 5.08 cm at the other. The pressure head at the smaller end is 4.88 m of water. If water flows through this cone at a rate of 125.6 ft3/sec, find the a. Reynolds number of the piping system b. Height (in ft) in the larger piping system

Q: Question: The pressure pipe elbow with 30 degree orientation in the vertical plane is 60 cm in…

A: Solution

Q: 2. Consider the piping network shown. The pressure heads at points A and B are 80m and 52m,…

A: Pressure head at A, hA=80 m Pressure head at B, hB=52 m Head loss, H=80-52=28 m Hazen William…

Q: An 8 in diameter (f=0.028) 500 ft long discharge a 3 in diameter water jet into the atmosphere at a…

A: Using the continuity equation calculating the jet velocity: AV=AjVj…

Q: Figure Q4 shows there are two sections of pipes in the system, which are 38m long of 5 cm diameter…

A: Given, L1 = 38 m  L2 = 45 m D1 = 5 cm or 0.05 m D2 = 15 cm or 0.15 m \ Q = 0.005 m3/s

Q: A schematic of the branched pipes is shown in Figure 3. Unit 1 requires a pump placed in line to…

A:

Q: The flowrate of water through the bend pipe (90o) is 0.21 m3/s. The pipe diameter at the inlet is…

A:

Q: Water at 70°F passes through 0.75-in-internal diameter copper tubes at a rate of 0.4 lbm/s.…

A:

Q: In the parallel system shown, pipe 1 has a length of 3000 ft and 20-inch in diameter. Pipe 2 is 5000…

A:

Q: The pressure at point 2 shown in Figure is not to fall below 4.14 Bar when the flowrate from the…

A:

Q: Estimate the maximum water hammer pressure generated in a rigid pipe of a 3 m dia pipe with an…

A: Given- Diameter of the pipe- d=3 m,L=8000 m,t=4 s,V=3 m/s, It is needed to find the critical time of…

Q: Q6. Absolute vapor pressure of water siphoned is 2.25 kPa. Water is extracted from a reservoir as…

A: Given that: Vapour Pressure of water: Pv=2.25kPaAtmospheric Pressure, Patm = 100 kPaγwater =9810…

Q: (Flow through Single Pipes). Determine the flow in each pipe and the pressure at the junction node,…

A: g= 9.81m/s2 =32.19ft/s2

Q: In the parallel system shown, pipe 1 has a length of 3000 ft and 20-inch in diameter. Pipe 2 is 5000…

A: Solution:

Q: H.W(2):Water flows steadily from a large tank through a pipe that splits into two smaller pipes as…

A: Given data in question  Water Depths Diameter  To find out  Pressure at point 1 Discharge through…

Q: Water flows from the ground floor to the third floor in a 4-storey building through a pipe 50 mm in…

A: Discharge, Q=2 L/s Diameter of the pipe, D=50 mm Roughness coefficient, k=0.03 mm Opening diameter…

Q: Pipe in Series: Consider the two reservoirs show in below figure, connected by a single pipe that…

A: Z1-Z2= 9 mD1= 200 mmD2= 250 mmL1= 15 mL2= 45 mKLen= 0.5KLex= 1f= 0.01

Q: Water flows from the tank shown in the figure below. At a depth of 1.5 ft the rate of change of…

A: Total length of pipe= 18ftDiameter of pipe = 0.4 inFriction factor = 0.03Loss coefficient For…

Q: (3) Water jet 0.05 m- (2) 0.8 m •(1) 8X.X kPa 0.1 m Figure Q2 (b) (i) Determine the flow rate at the…

A:

Q: 1. For the frictionless syphon shown, determine the discharge and the pressure heads at A and B.…

A:

Q: Nozzle

A: To calculate pressure head at point 2. Applying Bernoullis equation at point 2 and exit. Note that…

Q: In the following system, the flow rate of Q = 400 It / s is transmitted from the A chamber to the B…

A: The liquid from one chamber to another chamber due to variation in height and pressure…

Q: For the piping system shown below, determine the flow distribution and the piezometric heads at the…

A:

Q: 2. A tank and piping system are shown below. The total length of PVC pipe is 2500 ft and discharges…

A: We have to find the pressure at A in the mid point of the pipeline according to the given data like…

Q: For the piping system shown below, determine the flow distribution and the piezometric heads at the…

A: We have to find the value of flow distribution and the piezometric head at the junction j according…

Q: A liquid of specific gravity SG = 1.54 flows in a 13 cm diameter horizontal pipe. The total energy…

A: Specific gravity of liquid, SG =1.54Diameter of pipe, D =13cm =0.13mThe total energy at a point in…

Q: c) A reservoir of water is connected to a 12 inch diameter pipe 50 feet long and capped at the end.…

A: Note:- Hi! Thank you for the question As per the honor code, We’ll answer the first question since…

Q: Problem 3 For the series/parallel pipe system shown, determine the total head loss in the system if…

A:

Q: Water is pumped up from a reservoir to a smaller holding tank. If the flow rate through the pipe is…

A: NPSH is the net positive suction head, which is measured in the centrifugal pump.If the local…

Q: B: A closed cylindrical tank filled with water has a hemispherical dome and is connected to an…

A: Asked: To determine the pressure in pipe B and the pressure head, in millimeters of mercury, at…

Q: Given below are pipe lengths, sizes and connections. All pipes have a friction factor of 0.020. If…

A: Given Data:Friction Factor=0.020V=8cfsPipe 1length=2750ftdia=21inPipe 5length=4750ftdia=27in

Q: For the piping system shown below, determine the flow distribution and the piezometric heads at the…

A:

Pressurized pipe flow

A 15-kilometer-long pipe with a pipe diameter of one meter transports water at a speed of one meter per second. The pipe has a friction coefficient of 0.005. Calculate the frictional head loss?