Assume a 20 MHz Fcy and a prescaler value of 8 for Timer2 operating in 16 bit mode. Also assume that an output compare module has been configured for pulse width modulation using a 10ms period. WhatOCXRS register value is required to produce a pulse width of 5ms? a) 12,250 Ob) 11,764 Oc) 12,650

Assume a 20 MHz Fcy and a prescaler value of 8 for Timer2 operating in 16 bit mode. Also assume that an output compare module has been configured for pulse width modulation using a 10ms period. WhatOCXRS register value is required to produce a pulse width of 5ms? a) 12,250 Ob) 11,764 Oc) 12,650

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Related questions

Q: 3. Define a one-byte variable-type signal. 4. Define a signal of constant type and give it the value…

Q: The information in an analog signal voltage waveform is to be transmitted over a PCM system with an…

A: Given, Analog signal voltage waveform is to be transmitter over a PCM system. Accuracy is ∆2=±0.1%…

Q: h) Which of the following best describes EPROMS? 1. EPROMS can be erased by UV. 2. EPROMS can be…

A: EPROM stand for Erasable Programmable Read Only Memory. EPROM is Erasable but it can be…

Q: 89 Output voltage of an inverter is controlled by multiple pulse modulation technique. If the peak…

Q: Bandwidth of the input to pulse code modulator is restricted to 4 kHz. The input varies from -3.8V…

A: We need to find out the number bits per sample for given pcm signal

Q: Q2, (a) Design a comparator to compare two eight bit numbers? Draw complete gate level diagram? |

A: consider the given question;

Q: Exampic Bandwidth of the input to pulse code modulator is restricted to 4 kHz. The input varies from…

A: We need to find out the number of bits per sample for given pcm signal . First we will find out step…

Q: 13. The purpose of the __________ is to periodically sample the continually changing analog signal…

A: 1) The purpose of the quantisation is to periodically sample the continually changing analog signal…

Q: In single pulse modulation of PWM inverters, the pulse width is 120°. For an input voltage of 220 V…

A: It is given that:

Q: Assume a 16MHz Fcy and a prescale value of 64 for Timer2 operation in 16 bit mode. Also assume that…

A: Given Data: Frequency of the Crystal Oscillator Fcy=16 MHz Prescale value =64 The time period of…

Q: 5. Let an input signal into a 50-Hz PCM system is 8.5 Vp-p and level of quantization is set to 16.…

A: Solution : L= number of quantization of the PCM m(t ) = Vpp = Dynamic Range = 8.5 V fm= 50…

Q: KS ) For three input timing diagram shown below, do three of the following logic operations and draw…

A: Timing diagram is drawn for two cycles,as the given waveforms are periodic.for remaining cycles same…

Q: . A linear sign-magnitude PCM code consists of a. all magnitude bits b. a sign bit and magnitude…

A: 11) A linear sign-magnitude PCM code consists of a sign bit and magnitude bits ( option B).

Q: 8. Which characteristic of IC in Digital Circuits represents a function of the switching time of a…

A: The solution is provided in the following section.

Q: , …. 1210). The counter has the following features: a synchronous Active High Reset a value R can…

A: Write VHDL code for a modulo-13 counter (counting sequence is 010, 110, …. 1210). The counter has…

Q: certain clocked FF has minimum ts = 20 ns and tH = 5 ns. How long must the control inputs be stable…

A: The explanation is as follows.

Q: An ADC has a 0 to 14.5-volt input with a(n) 13-bit output. What would the binary value 00..0111…

A: The solution is given below

Q: Select all the 8088 input signals that can cause the microprocessor to take an interrupt. O INTR OSC…

A: The 8088 input signals that can cause the microprocessor to take an interrupt is INTR, INTA, and…

Q: How do you differentiate digital modulation from analog modulation?

A: A message signal is transferred from the sender to the receiver end. The signal is transmitted…

Q: After analysis, it is correct to state that this is a (image attached): (a) six-bit decoder. (b)…

A: The digital circuits can be combinational as well as sequential circuits. The combinational circuits…

Q: Assume you want to use Timer 1 to generate a mode 6 (9 bit Fast mode PWM) signal. What is the…

A: Given clock CPU feequency = 8 MHz Time to produe minimum frequency to generate fast mode PWM signla…

Q: 3.1) How many PIC24 Timer2 ticks are equal to 1.2 ms assuming a prescale of 8 and a Fcy of 30 MHz?…

A: “Since you have asked multiple question, we will solve the only one question for you. If you want…

Q: Q2) B) Use the SAR ADC to convert the analog voltage of (7.28 V) to 8-bit binary. If (VREF = 10V),…

A: Given, Analog input voltage Vin=7.28 V Reference voltage Vref=10 V

Q: 8. Which characteristic of IC in Digital Circuits represents a function of the switching time of a…

A: The solution is provided in the following section.

Q: You have a 16-bit timer and you want to configure it to generate an interrupt at a rate of 500 Hz.…

A: MSP430 is an ultra low power micro controller. It is a mixed signal processor with RISC…

Q: A combinational circuit that selects binary information from one of many input lines and directs it…

A: Combinational Circuit A combinational circuit is a logical circuit that combines a diffirent gate…

Q: b) A modulated signal of x(t) = 6cos(300nt)cos(4800nt) + 30 is converted to a digital %3D signal…

Q: 8. Which characteristic of IC in Digital Circuits represents a function of the switching time of a…

A: The solution is provided in the following section.

Q: How is Pulse Width Modulation (PWM) useful in microcontroller applications?

A: We need to explain uses of PWM in microcontroller applications.

Q: Q9- Complete the following timing diagram for the circuit shown below. Assume a small delay for…

A: The D Flip-Flop circuit diagram is shown below, Here, all the inputs and signals are active high.

Q: Bandwidth of the input to pulse code modulator is restricted to 4 kHz. The input varies from -3.8V…

A: We need to find out the number of bits per sample for given signal to noise ratio and given signal…

Q: Show all the necessary details

A: Given, Here, the reference voltage is Vref=6 Volts given above in the question. and the Analog…

Q: Suppose that the Fast PWM mode is to be used where (i) the TOP value for timer 1 is given in ICR1,…

A: Fast PWM mode:- In this mode timer counts from 0 to 255. It is based on the single-slope operation.…

Q: xplain the concept of pulse-width modulation (PWM) in microcontroller programming. How is PWM used…

A: we need to explain:the concept of pulse-width modulation (PWM) in microcontroller programming.How is…

Q: In a PCM system, the maximum frequency of the analog input signal is 4 kHz. If the number of…

A: Given that Maximum frequency of the analog input signal (fm) = 4 kHz Quantization level=2 =2n So…

Q: A 16-bit successive approximation ADC is to be designed to operate at 50,000 conversions/second.…

A: Given Nmax=50,000 conversion/s Calculating conversion time TT=1NmaxTT=150,000 conversion/sTT=2×10-5…

Q: 8. Which characteristic of IC in Digital Circuits represents a function of the switching time of a…

A: Answer: d) Propagation delay Explanation: a) It is not a valid option. The Fan-out is the…

Q: Which module of the microcontroller will definitely be used if an analog signal needs to be read in…

Q: of tion of ation of stion The sensitivity of the LM35 Temperature Sensor Module is 10mV/C. If the…

A: 1. Option 250mV is the correct answer The specifications of LM35 temperature sensor module for the…

Question

Assume a 20 MHz Fcy and a prescaler value of 8 for Timer2 operating in 16 bit
mode. Also assume that an output compare module has been configured for pulse
width modulation using a 10ms period. WhatOCXRS register value is required to
produce a pulse width of 5ms?
a) 12,250
b) 11,764
Oc) 12,650
d) 12,500

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Given data:-

VIEW

Step 2: Calculation :-

VIEW

Solution

VIEW

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Which shift keying technique is used in the following diagram? Briefly explain:
15. a. In Figure 2, The counter mode is ...(single step or free run ) b. In Figure 2, The counter count mod is .. . c. In Figure 2, Which leds are on after five clock pulse? Explain in detail. PC1 PC2 INPUT OUTPUT OUTPUT GHIJKL MNOPOR GHIJKL MNOPO R 230050 4G 11 DeDerer 131 Clock Rulser Up Counter CLOCK DATA LOAD CLOCK EMABL unter DATA A bale NIDA CerP NIDA Cerp. Figure 2 S1U→USX
answer the ff. tnxxxxxxx
4 -This digital circuit (image attached) is a: Choose an option:A. asynchronous counter from 0 to 5.B. synchronous counter from 0 to 6.C. 4-bit serial input shift register.D. asynchronous decade counter.E. modulo counter 8.
Subject: Circuits INote:Support the problems with circuit diagram and label the pertinent parts and also complete solution so that i can learn too
Draw a clock signal CLK with five 0-to-1 timing events, a nonzero setup time, tsu, and a nonzero hold time,th. Also draw one excitation input signal EI that follows the sequence 10110 and meets the setup and hold timerequirements. In the excitation input, the first bit in the sequence (1) occurs in time for the first clock timingevent, the second bit in the sequence (0) occurs in time for the second clock timing event, and so forth.
Calculate the capacitance of the circuit below.
Q1. Design asynchronous (ripple ) binary counter and timing diagram for the following sequence (0,1,2,3,4,5) Q2. Determine the resolution expressed as a percentage of 16-bit DAC.
Define the following terms