Assignment#4Refer to Electronic Devices, Floyd chapter 12 and 131.Two IC op-amps are available to you. Their characteristics are listed below. Choose the oneyou think is more desirable.Op-amp 1: Zin = 5 MM, Zout = 1000, Aol = 50,000Op-amp 2: Zin = 1010MQ, ZoutMQ, Zout = 75 Q, Aol150,000=2.An op-amp datasheet specifies a CMRR of 300,000 and an Aot of 90,000. What is the common-mode gain?3.How long does it take the output voltage of an op-amp to go from -10 V to +10 V if the slewrate is 0.5 V/µS?4. Determine Av, Vout, Iin and If :VinIVR₁www2.2 ΚΩ+Rfwww22 ΚΩOV out

Given Data:The characteristics of 2 Op-Amps as,Op-Amp122. An Op-Amp with,Common Mode Rejection Ratio…

Assignment#4 Refer to Electronic Devices, Floyd chapter 12 and 13 1. Two IC op-amps are available to you. Their characteristics are listed below. Choose the one you think is more desirable. Op-amp 1: Zin Op-amp 2: Zin = 5 MM, Zout = 1000, Aol = 50,000 10 ΜΩ, Zour 75 , Aol = = = 150,000 2. An op-amp datasheet specifies a CMRR of 300,000 and an Aot of 90,000. What is the common- mode gain? 4. Determine Av, Vout, Iin and If : 3. How long does it take the output voltage of an op-amp to go from -10 V to +10 V if the slew rate is 0.5 V/µS? Vin 1V Iin R₁ ww 2.2 ΚΩ Rf www 22 ΚΩ

Assignment#4 Refer to Electronic Devices, Floyd chapter 12 and 13 1. Two IC op-amps are available to you. Their characteristics are listed below. Choose the one you think is more desirable. Op-amp 1: Zin Op-amp 2: Zin = 5 MM, Zout = 1000, Aol = 50,000 10 ΜΩ, Zour 75 , Aol = = = 150,000 2. An op-amp datasheet specifies a CMRR of 300,000 and an Aot of 90,000. What is the common- mode gain? 4. Determine Av, Vout, Iin and If : 3. How long does it take the output voltage of an op-amp to go from -10 V to +10 V if the slew rate is 0.5 V/µS? Vin 1V Iin R₁ ww 2.2 ΚΩ Rf www 22 ΚΩ

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Calculate current gain, input and output impedance, and linearity. Beta = 90 IS = 2E-15
16 digital electronics Which of the following is true about the noise margin according to the figures given in the figure? b) the question is wrong d) none
An Op-amp has a slew rate of 5 V/microsec. The largest sine wave output voltage possible at a frequency of 1 MHz is ?
1-C) Which op-amp IC is more suited for digital applications, and why?1-D) Which op-amp IC is more suited for instrumentation applications, and why?
R, R. R, out R. R. out out 20kn Figure 3 Figure 1 Figure 2
Calculate the dc and ac components of the output signal across load RL in the circuit of Figure * Va = 150 V V, (ms) = 15 V V's V', (ms) R 500 2 Full-wave rectifier C, 15 μF C2 10µF RL 5 ka O vdc= 136.4V, Vac= 3.9V O Vdc= 163.4V, Vac= 9.3V Vdc= 13.4V, Vac= 9.9V O None of the above
(Asterisked problems are associated with optional sections.) 1. Determine the output of each of the following circuits, assuming that the upper input is 1 and the lower input is 0. What would be the output when the upper input is 0 and the lower input is 1? a. b. C. D D nia 00
... .. 0 O .. . . .O .. . e A student intends to connect a TL082 OP-AMP as a voltage follower, to "follow" the voltage generated by a potentiometer but makes some mistakes in the breadboard wiring: *He took Pin 3 and connected it to Pin 1, but this is wrong as Pin 3 is supposed to go to Pin 6, fix this. *A meter lead is supposed to go to Pin 6, the output not to Pin 1. A 3rd mistake results in no output but this he cannot discover, help him. Sketch a schematic diagram of this circuit, fixing the above (don't forget to include the Voltmeter) and determine what the voltmeter's indication will be, explaining why it is such. 12 V TL082 12 V AA OFF COM
A circuit diagram of the Wein bridge oscillator is shown in figure 6. Derive thenecessary conditions for oscillation in this circuit if C1C2= a, R1R2=1b
For the circuit shown in below, determine and sketch the output waveform for the give input signals: - Vini = 2 sin(wt) Vinz = 1 volt 100 k Ohm 50 k Ohm V_out 50 k Ohm V_in1 100 k Ohm V_in2
For opamp which has input voltages Vi1 = 160 µV Vi2= 50 µV Differential gain Ad= 80 CMRR= 1.00e3 Please calculate the output voltage. Please give the answer in µV, do not include anything else than the answer and the format will be 0.01e+6 or 1.02e-4.
Choose any 4 Questions. Where appropriate, use figures and equations to aid explanation 1.a. What are the two comparator reference voltages in a 555 timer when Vcc = 10 V? 1.b. Determine the frequency of oscillation for the 555 astable oscillators in Figure. 1.c. To what value must Cext be changed to achieve a frequency of 25 kHz? +5.5 V 1.0 kn R₂ • 3.3 ΚΩ Cest 0.047μF RESET DISCH THRESH TRIG 555 GND Vec OUT CONT C₁ 0.01 F 1.d. In an astable 555 configuration, the external resistor R1 = 3.3 k. What must R2 equal to produce a duty cycle of 75%.