Assignment 2-M Figure: The composite member is shown in the figure. If the rigid bar remains horizontal after the loading is applied and a temperature change of +10°C. Determine the total stresses on each of the vertical members considering actual stress due to the loading carried and due to temperature change. Given on the table below are the properties of each material used as members. (steel) 500 mm 120 kN 150 mm 150 mm Steel Rigid Brass (rigid bar) 250 mm Area (mm2) 700 3000 (brass) E (GPa) 200 100

Assignment 2-M Figure: The composite member is shown in the figure. If the rigid bar remains horizontal after the loading is applied and a temperature change of +10°C. Determine the total stresses on each of the vertical members considering actual stress due to the loading carried and due to temperature change. Given on the table below are the properties of each material used as members. (steel) 500 mm 120 kN 150 mm 150 mm Steel Rigid Brass (rigid bar) 250 mm Area (mm2) 700 3000 (brass) E (GPa) 200 100

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

1. Three metal strips, each 40 mm height, are bonded together to form the composite beam shown. The modulus of elasticity is 210 GPa for the steel, 105 GPa for the brass, and 70 GPa for the aluminium. If the allowable bending stress for the aluminum (Gallow)al= 100 MPa, for the steel (Gallow)s=150 MPa and (Gallow)b= 200 MPa for brass determine the maximum allowable intensit of w of the uniform distributed load. 2w Aluminum 2w 10 mm Brass 10 mm Steel 20 mm 2m - 40 mm
The composite bar in the figure is stress-free before the axial loads P1 and P2 are applied. Assuming that the walls are rigid, calculate the stress in each material if P1 = 150 kN and P2 = 90 kN.
1. Find the properties of equal-leg angle bar 150 x 50 x 6.0 in metric. 2. Find the full section properties of LC shapes steel bar 100 x 50 x 15 x 3.0 in metric. 3. A stress that lies between the proportional limit and the upper yield point of a steel. What is 5 and 5 Show the relationship uring a graph of mild structural stool
As shown in the figure below, a bronze bar is affixed between a steel bar and an aluminum bar. Axial loads are applied at the positions indicated. If the largest value of P that will not exceed an overall deformation of 4.0 mm, or the following stresses: 150 MPa in the steel, 130 MPa in the bronze, and 90 MPa in the aluminum, determine the stress in the bronze. Assume that the assembly is suitably braced to prevent buckling. Use Est = 200 GPa, Eal = 70 GPa, and Ebr = 83 GPa. (The correct answer is 71.36 MPa. Can you show the solution? Thank you!)
#2 will upvote to anyone who will answer
A combined section of steel and copper is subjected to a compressive load. Refer to the table below for the properties of each Steel Copper Area, A 900 mm2 1,200 mm2 Modulus of elasticity, E 200 GPa 120 GPa Allowable compressive stress 140 MPa 70 MPa If the allowable strain for both materials is 0.0005, which of the following most nearly gives the maximum load the member can carry so that this allowable strain is not exceeded? Select the correct response 162.00 kN 185.00 kN 205.00 kN 175.00 kN
Mechanics of Deformable Bodies Show complete and detailed solution. Write legibly. Draw illustrations. Follow the decimals places on the direction
10/10 FIND STRESS IN STEEL MATERIALS IN COMPOSITE COLUMIN SHOWN BELOW. IF E st= 200 kN/MM2, Ealu.=70 kN/MM2 100 kN RALU=30 MM Aluminum Steel 1m R ST 20 MM
Getting measurements from Figure , determine approximate values of the following items for steel with different carbon contents. Use one system of units only as specified by the instructor.a. Yield stressb. Ultimate strengthc. Strain at failured. Effect on modulus of elasticitye. Approximate toughness. Curves may be approximated with a series of straight lines.f. Comment on the effect of increasing carbon content on items a through e above.
Show Stress/ strain curve for nitinol and steel (2 separate charts please)
If the modular ratio is equal to 7, and the Modulus of Elasticity of the Steel is 200,000 MPa. What is the value of fc'?
A composite beam is made of two brass [E = 120 GPa] bars bonded to two aluminum [E = 70 GPa] bars, as shown. The beam is subjected to a bending moment of 400 N-m acting about the z axis. Using a = 15 mm, b = 100 mm, c = 30 mm, and d = 65 mm, calculate (a) the maximum bending stress in the aluminum bars. (b) the maximum bending stress in the brass bars. Aluminum y Brass Aluminum b Brass C a d