Asap thank you. a. Ordinate of the influence line of RC at point D b. Ordinate of the influence line of RE at point B c. Ordinate of the influence line of MD at point F.

Q: * Assignment Construct the influence line for the vertical reaction at B and A, separately, of the…

A:

Q: 50 kN 50 kN B 20 kN/m 1 m 4 m 1m

A:

Q: Draw the influence lines for the forces in the members identified by an "x" of the tru shown in the…

A: An Influence line Diagram shows the influence of effect due to load on the reactions, shear force or…

Q: B fm fm Draw the influence line for the beam Use Müller-Breslau's Method 1 Reaction at A 2 Reaction…

A:

Q: The beam is used to support a dead load of 2 k/ft, a live load of 2 k/ft, and a concentrated live…

A: since the given question has multi-parts therefore as per guidelines only 1-3 part will be solved.…

Q: The designed to withstand a uniformly distributed live load of 60 kN/m, a dead load of 20 kN/m, and…

A:

Q: A 2.5' Ay Vc when unit load is egment AC: A Ay = 1- 2.5' C X 10 M 7.5' с Msection = 0 X 10 -Vc + -…

A:

Q: In the influence line of V at D, the ordinate of this influence line at point F equals *

A:

Q: Problem 2 The truss shown carries the following uniform live load and concentrated live load. E F 3…

A:

Q: Use the Müller-Breslau principle to sketch the nfluence lines for the vertical reaction at A, the…

A: Given data in question  Beam Internal hinges To find out  ILD for RA , VE- and MA using Muller…

Q: Using the equilibrium method (write equations), draw the influence lines for the following response…

A:

Q: 11. Draw the influence lines for the forces in the members identified by an "X" mark of the truss…

A: ### Drawing of ILD for the forces in the members identified by X as GH , CH, CD, HD ###of given…

Q: Sketch the influence lines for the vertical reaction at A, the shear at B, and the moment at B

A:

Q: A mmmmm B 5.0m C "b" D 3.0m E "2" F

A:

Q: find all reaction for the frame by the force method

A: Let's take Hc as redundant  Using Theorem of least work (Force Method)

Q: A rectangular beam has a dimension of 210 mm x 260 mm. The simply supported beam is 5-m long and…

A: To Determine Maximum flexural stress of the beam.

Q: A moving vehicle traverse on a bridge supported by the beam below. a. Construct the influence line…

A:

Q: The beam supports a uniform dead load of 3kN/m, a concentrated live load of 8kN, and a uniform live…

A:

Q: 3. Draw the influence lines for the vertical reactions at supports A and E, the reaction moment at…

A: In this question we are asked to draw  ILD of given stress functions

Q: Draw the influence line for (internal) bending moment MA. Enter the magnitude of your influence line…

A:

Q: Question 2: Draw the influence line for the force in member DK. L K H A 1.5 m B] -2 m D F -2 m -2 m…

A:

Q: In the influence line of V at D, the ordinate of this influence line at point B equals * A Hinge В D…

A: To find:- ordinate at B for ILD of V at point D.

Q: w = 9 - P = 24 1. Draw the influence line of the beam shown below for a uniform load of w kN/m for…

A:

Q: For the truss shown below draw the influence lines for Ay, Ey, FAH and FBC for a moving load between…

A:

Q: D A В E wwww ......... .... . 3m 6m 4m

A:

Q: Determine quantitatively the influence lines for Ay, ME and VẸ for the statically determine system…

A: Data given: Asked: Influence lines for Ay, ME and VE

Q: Select the correct influence line diagram for shear force at x of the following beam: (a) (b) (c)…

A:

Q: Influence Lines. , (a) For the determinate beam shown below, draw the Qualitative influence lines…

A: Influence line represents variation in Forces w.r.t Load.

Q: MAJAOS g B -008- 50° 60° D SS.S bnp (SS awodz 290101 Fig. P2.26 a The hydraulic cylinder BD exerts…

A:

Q: Example Draw the influence lines for the for reaction at support A ( RA), shear force at point D (…

A: Given data in question  Proppee cantilever beam  Span member length  Internal hinge To find out…

Q: Draw the influence line for shear force VE. Enter the magnitude of your and G influence line when…

A:

Q: Draw the influence line of support reaction C for the beam in figure 12. El is constant A/ B C 6m 6m

A: a) Indeterminate beam b) Primary beam subjected to unit load at B

Q: VI. Skecth the influence lines for reactions RA and MA at the fixed support at A and for reaction Rc…

A: Given data,beam is given with internal hinge at B and free end at DFINDILD for reaction at AILD for…

Q: 50 kN 50 kN B 20 kN/m D 1 m 4 m 1m

A:

Q: 4. Sohe for the Reaction at A and B in he Cartikver Beam Shown KNm 30 KNim 120 KN 1.50 m 4.50 meten

A:

Q: 2. Find and draw influence lines of Fcd, and the vertical component of Fec- A B C D E F 5 m d e 6 at…

A: Consider the free body diagram as;

Influence Lines

The graphs that show the variation of a function at a specific point on a beam or truss due to a unit load placed at any point along the structure are known as influence lines in engineering. Some common functions that are studied with influence lines are shear, moment, and deflection. In designing beams and trusses, it is important to use influence lines in structures where loads would move along their span such as bridges, crane rails, conveyor belts, floor girders, etc. The influence lines help to study where a load will create the maximum effect for any of the functions.