As shown in the figure, there is a gap between the aluminum bar and the rigid slab that is supported by two copper bars. At 10°C, A = 0.18 mm. The temperature in the assembly is increased to 95°C. Neglect the mass of the slab. For each copper bar, A = 500 mm², E = 120 GPa, and acopper = 16.8 x 10“ m/(m.°C). For Aluminum bar, A = 400 mm, E = 70 GPa, and Caluminum = 23.1 x 10°m /(m.°C). Determine the stress in the aluminium bar in MPa. Determine the stress of copper in MPa %3D %3D %3D %3D AT Copper Copper 750 mm

As shown in the figure, there is a gap between the aluminum bar and the rigid slab that is supported by two copper bars. At 10°C, A = 0.18 mm. The temperature in the assembly is increased to 95°C. Neglect the mass of the slab. For each copper bar, A = 500 mm², E = 120 GPa, and acopper = 16.8 x 10“ m/(m.°C). For Aluminum bar, A = 400 mm, E = 70 GPa, and Caluminum = 23.1 x 10°m /(m.°C). Determine the stress in the aluminium bar in MPa. Determine the stress of copper in MPa %3D %3D %3D %3D AT Copper Copper 750 mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: A solid compound bar (which is made of an aluminum segment and a bronze segment) is fixed to a rigid…

Q: Q3: The rigid bar ABC in the Figure is pinned at B. Initially, the bar is horizontal. If the…

A: Area of cable Ac=200 mm2angle tanθ=34θ=36.869°Steel rod length L=6 m or 6000 mmAsteel=500 mm2…

Q: A circular plate with simply supported edges subjected to a uniform pressure of P=1,450 KPa, as…

Q: A steel rod 15mm diameter is held snugly (but without any initial stresses) between rigid walls by…

A: Answer: (a) The temperature drop required is 29.33 ℃. (b) The bearing stress in the bolt and clevis…

Q: At a temperature of 11°C, a 2-mm gap exists between two polymer bars and a rigid support, as shown…

Q: Rigid bar BC is supported by aluminum rod (1) and bronze rod (2), as shown in the figure. Aluminum…

Q: een two rigid immo gure. The rod is pe

Q: Two bars are subjected to F=20 kN force as shown in Figure and a 0.5 mm 0.4 m 0.6 m temperature rise…

Q: 0.5 mm 0.4 m 0.6 m F=20 kN Bronze A = 1500 mm2 E = 105 GPa a = 21.6 x 10-c Aluminum A = 1800 mm2 E =…

Q: a) Find the temperature change in the steel and aluminium rods when the lower end of the aluminium…

Q: Problem. The bone of the dog has the length L = 20 cm, surface of = 2.8 cm, and Young's modulus Y =…

Q: steel bar is held by two fixed supports as shown ne figure and is subjected to an increase…

A: Given:Temperature rise is ∆T=100o Cthermal expansion is α=11×10-6 /o Celastic modulus of the…

Q: Engineer firms in many situations must verify the reliability of existing purchased designs. Your…

Q: A vessel is pressurised at A. The ends of the vessel are shut with two-disc plates connected by the…

A: Given P=6.8 MPaE=210 GPaR=80 cm(Radius of vessel ) =D=160 cm t=12 mmd=12 cm (diameter of shaft )

Q: The roof over a 9.0-m x 10.0-m room in a school has a total mass of 12900 kg. The roof is to be…

Q: As shown, there is a gap between the aluminum bar and the rigid slab that is supported by two copper…

Q: 2. A rigid bar of negligible weight is supported as shown in the figure. If W = 60 kN, compute the…

Q: As shown in the figure, there is a gap between the aluminum bar and the rigid slab that is supported…

A: Given data: T0=10°C∆=0.18 mmT=95°CFor each copper bar:A=500 mm2E=120 GPaα=16.8 μm/m°CFor each…

Q: As shown in Fig, there is a gap between the aluminum bar and the rigid slab that is supported by two…

A: Given data as per question Area of copper rod =500 mm2 Area of aluminium rod =400 mm2 we know that…

Q: A flat steel plate that weighs 1.0 N is resting on top of an aluminum ball which is resting on a…

A: Solution: Given Data: *The weight of the steel plate, W=1 N *The diameter of the ball is, D = 100 mm…

Q: Bar A has a cross-sectional area of 0.04 m2, modulus of elasticity E = 70 GPa, and coefficient of…

A: Given Data αA = 14 E‐6 C-1 αB = 16 E‐6 C-1 b=0.4 mm LA=LB=1 m

Q: The rigid bar ABC is supported by a hinge at B and two vertical steel rods at A and C as shown in…

Q: L = 3 m Figure P-265

Q: A prismatic bar with a length L = 1 m andcross-sectional area A = 1200mm2 is supported atthe ends.…

A: If the temperature of the body is lowered or raised its dimension will increase or decrease…

Q: A 23 mm diameter bronze bar 2.8 m long is placed between two rigid walls. At a temperature of -3°C,…

Q: Consider a steel bar attached at both ends. Assume that at 20 °C this bar is free of tension.…

A: Thermal stresses generated due to a temperature increase fromT1 to T2 is given byσ=E∝ T2-T1where…

Q: A rigid bar of negligible weight is supported as shown in Fig. P-271. If W = 80 kN, compute…

Q: A bronze bar 3 m long with a cross sectional area of 320 mm² is placed between two rigid walls as…

A: Given: Initial length of the rod→L=3 m Cross sectional area of the bar→A=320 mm2 Initial temperature…

Q: SAMPLE PROBLEM 4.5 Thermal Stresses in a Tube A 10-in. length of steel tubing (with properties of E=…

Q: (E, = 200 GPa, a, =11.7×10°C) have the dimensions shown at a temperature of 20°C. The steel rod is…

Q: A 480-N uniform rectangular sign 4.00 m wide and 3.00 m high is suspended from a horizontal,…

A: Given data as per question Weight of block = 480 N Weight of rod = 110 N Angle =300

Q: Q3: A rigid beam ABCD is supported as shown. Initially and at room temperature the beam is…

Concept explainers

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.

Question

As shown in the figure, there is a gap between the aluminum bar and the rigid slab that is
supported by two copper bars. At 10°C, A = 0.18 mm. The temperature in the assembly is
increased to 95'C. Neglect the mass of the slab.
For each copper bar, A = 500 mm², E = 120 GPa, and acopper = 16.8 x 10° m/(m.'C).
For Aluminum bar, A = 400 mm', E = 70 GPa, and aaluminum = 23.1 x 10°m /(m.'C).
%3D
%3D
Determine the stress in the aluminium bar in MPa. Determine the stress of copper in MPa.
ww OSL
addo)
Aluminum
Jaddo)

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Problem (8) The rigid bar ABC in the figure is Figure P-268 pinned at B and attached to the two vertical rods. Initially, the bar is Steel L = 0.9 m A 300 mm2 E = 200 x 10 N/m2 a 11.7 um/(m-°C) Aluminum L = 1.2 m A = 1200 mm² E = 70 x 10 N/m2 α- 23 μη/ (m."C) horizontal and the vertical rods are stress-free. Determine the stress in the aluminum rod if the temperature of the steel rod is decreased by 40°C. Neglect the weight of bar ABC. Solution: 0.6 m 1.2 m
Q2: A brass rod of 4m length is fixed at both ends. Calculate the temperature through which the rod should be heated if the thermal stress is not to exceed 100 MPa. Take the coefficient of linear thermal expansion a=20x10-6/K and modulus of elasticity for brass equal to 90 GPa.
A steel cylindrical pressure vessel with closed ends is 25 cm external diameter and 5 mm thick It is wound closely with a single layer of circular wire of diameter 1.2 mm. Under the tension of 96 N/mm'. If the cylinder is treated as thin. Calculate (1) Initial stress in cylinder. (ii) Initizl pressure which will produce a stress of 48 N/mm2.
5mm width. Rectangular cross section.
Thank you. Please help me.
3. Three bars each made from different materials are placed between walls when the temperature is 14°C. Determine the support reaction when the temperature becomes 19°C. The material properties are given in the figure. Answer: R = 3502.30 N Steel Brass Copper Ebr 100 GPa Ecu = 120 GPa Est=200 GPa ast = 12(10-6)/°C abr = 21(106)/C acu = 17(10-6)/°C Acu = 515 mm² |Ast = 200 mm² Abr= 450 mm² -300 mm- 200 mm- 100 mm 4. The rigid slab is supported by two identical copper rods as shown. The copper rod has an area of 500 mm² with a = 16.8 μm/ (m°C) and E = 120 GPa. There is a gap of 0.18 mm between the slab and the aluminum rod. The aluminum rod has an area of 400 mm² with a = 23.1 μm/ ( mºC) and E = 70 GPa. Compute the stress developed in each rod when the temperature is raised to 85°C. Assume that the weight of the slab is negligible. Answer: OAI = 16.80 MPa 85 →TA Δ Copper Aluminum Copper 750 mm-
The rigid bar AC is supported by two axial bars (1) and (2). Both axial bars are made of bronze [E = 100 GPa; a = 18 × 10-6 mm/mm/ °C). The cross-sectional area of bar (1) is A1 = 184 mm2 and the cross-sectional area of bar (2) is A2 = 380 mm2. After load P has been applied and the temperature of the entire assembly has increased by 38°C, the total strain in bar (2) is measured as 1240 µɛ (elongation). Assume L1 = 1290 mm, a = 590 mm, b = 820 mm, and L2 = 2000 mm. Determine: (a) the magnitude of load P. (b) the vertical displacement of pin A. L2 (1) L1 B a P Answers: (a) The magnitude of P = i kN. (b) The vertical displacement of pin A = i mm (down).
Q3: A rigid beam ABCD is supported as shown. Initially and at room temperature the beam is horizontal and carries no load. Calculate the force in the rods when the temperature of aluminum rod only is raised by 120°C. Steel Wire A- 50 mm E-200 Gpa L-2 m Brass Rod 2. A-300 mm E-83 Gpa L-2 m a = 12um/m C Aluminum Rod Gap 2mm a- 19um/m C A=400 mm E= 70 Gpa L=3 m 23um/m C timt 1m Im
Kindly show a step-by-step solution. Thank you A 6m rod with a 4mm gap between one of its ends and the surface of the wall next to it is secured solidly between two walls at 25°C. Calculate the highest temperature that the rod can withstand in degrees celsius while taking into account the maximum limiting stress of 67 MPa, where a = 19.5 m/mC°, and E = 130 GPa.