As shown in the figure, there is a gap between the aluminum bar and the rigid slab that is supported by two copper bars. At 10°C, A = 0.18 mm. Neglecting the mass of the slab, calculate the stress in each rod when the temperature in the assembly is increased to 95°C. For each copper bar, A= 500 mm2, E = 120 GPa, and a = 16.8 µm/(m °C). For the aluminum bar, A= 400 mm2, E = 70 GPa, and a = 23.1 µm/(m °C). Copper Aluminum Copper 750 mm

As shown in the figure, there is a gap between the aluminum bar and the rigid slab that is supported by two copper bars. At 10°C, A = 0.18 mm. Neglecting the mass of the slab, calculate the stress in each rod when the temperature in the assembly is increased to 95°C. For each copper bar, A= 500 mm2, E = 120 GPa, and a = 16.8 µm/(m °C). For the aluminum bar, A= 400 mm2, E = 70 GPa, and a = 23.1 µm/(m °C). Copper Aluminum Copper 750 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A steel wire (E= 200 GPa) of diameter d= 1.25 mm is bent around a pulley of radius Ro= 500 mm. What is maximum stress in the wire?
1. As shown in the figure, there is a gap between the aluminum bar and the rigid slab that is supported by two copper bars. At 10°C, A = 0.18 mm. Neglecting the mass of the slab, calculate the stress in each rod when the temperature in the assembly is increased to 95°C. For each copper bar, A= 500 mm² E = 120 GPa, and a = 16.8 μm/(m °C). For the aluminum bar, A = 400 mm², E = 70 GPa, and a = 23.1 μm/(m. °C). Copper Aluminum Copper 750 mm
A steel bar is held by two fixed supports as shown in the figure and is subjected to an increased temperature of AT = 200°C. If coefficient of thermal expansion and young's modulus of elasticity of steel are 11 x 10-6/°C and 200 GPa respectively, the magnitude of thermal stress (in MPa) induced in the bar is
The rigid horizontal bar ABC of negligible mass is connected to two rods as shown in the figure. If the system is initially stress-free, calculate the temperature change that will cause a tensile stress of 90 MPa in the brass rod. Assume that both rods are subjected to the same change in temperature.
An aluminum shaft has a diameter of 50.1 mm. Determine the maximum shear stress in the shaft when subjected to a torque of 26.5 Nm? (answer in MPa or MN/m² to 1 decimal place, use pi = 3.142)
A steel wire (E = 200 GPa) of diameter d = 1.0 mm is bent around a pulley of radius Ro= 400 mm (see figure below). Ro a. What is the maximum stress in the wire? b. Does the stress increase or decrease if the radius of the pulley is increased?
3. An aluminum rod is rigidly attached between a steel rod and a bronze rod as shown in the figure. Axial loads are applied at the positions indicated. Find the maximum value of P that will not exceed a stress in steel of 140 MPa, in aluminum of 13.05 ksi, or in bronze of 100 MPа. Aluminum A = 400 mm? Bronze A = 200 mm Steel A = 500 mm? 2P 4D 2.5 m 2.0 m 1.5 m
Problem 1 An aluminum rod is rigidly attached between a steel rod and a bronze rod as shown. Axial loads are applied at the positions indicated. Aluminum Steel A=800mm2 A=1000mm2 Bronze A=700mm? 4P 2P 500mm 600mm 700mm 1. What is the maximum value of P that will not exceed the axial stress bronze of 105 MPa? 2. What is the maximum value of P that will not exceed the axial stress in aluminum of 90 MPa? 3. If P=10KN, what is the axial force to be carried by the aluminum in KN? 4. If P is 5KN, what is the axial stress of steel?
At room temperature (20°C) a 0.7-mm gap exists between the ends of the rods shown. At a later time when the temperature has reached 150°C, determine: (a.)The normal stress in the aluminum rod, (b.) The change in length of the aluminum rod. 0.7 mm 300 mm A Aluminum A =2,000 mm² E= 75 GPa α = 23 x 106/°C 250 mm B Stainless steel A = 800 mm² E = 190 GPa a = 17.3 x 10-6/°C
2. A copper rod of diameter 12 mm is subjected to a compressive force of 8 kN. The change in diameter happens to be 4.5 x 103 mm. Determine the strain along the length of the material and the Poisson's ratio when E = 110 GPa.
A 20 m long steel rod is at a temperature of 20°C. The rod is heated so that temperature rises by 50°C. If rod is allowed to expand by 14 mm, what will be the stress induced in rod? Take E = 200 GPa and α = 12 x 10-6/°C.
Two triangular wedges are glued together as shown in the figure. The stress acting normal to the interface, o, is MPa. 100 MPa 100 MPa on 45% 100 MPa -100 MPa