As shown in the figure below, Refrigerant 134a is contained in a piston-cylinder assembly, initially as saturated vapor. The refrigera is slowly heated until its temperature is 155°C. During the process, the piston moves smoothly in the cylinder. Patm = 1 bar Weight=471.1 N 0.00 n

As shown in the figure below, Refrigerant 134a is contained in a piston-cylinder assembly, initially as saturated vapor. The refrigera is slowly heated until its temperature is 155°C. During the process, the piston moves smoothly in the cylinder. Patm = 1 bar Weight=471.1 N 0.00 n

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A piston-cylinder device contains an ideal gas of nitrogen. At the initial state, the volume is V1= 1.00 m3, the pressure is p1= 400.00 kPa, the temperature is T1= 300.00 K. An electric heater within the device is turned on for a time of Δt = 5.00 min. The current is I = 3.00 A, and the source voltage is V = 120.00 V. During the heating process, the gas expands, and a heat loss of Qout = 2.80 kJ occurs. The gas constant is R = 0.297 kPa·m3/(kg·K), and the room temperature specific heat at constant pressure is cp =1.039 kJ/(kg·K). Calculate the mass of the gas, m__________ (kg)
Krypton in a closed system is compressed adiabatically from 74 K and 1 bar to a final pressure of 24 bar. What is the final temperature in K? Assume krypton is an ideal gas. From Appendix B in the text, we can assume the heat capacity of krypton is independent of temperature and CP=2.5R , where R is the molar gas constant R=8.314 J/(mol K). For an ideal gas, recall CV=CP−R=1.5R. Report your answer in units of K using three decimal places.
Either the system illustrated below where the fluid considered is water. 1. Calculate: (a) the internal energy (specific), and (b) the mass finally remaining in the volume of Control. 2. In the control volume, what is: (a) the specific internal energy of the saturated steam, (b) The specific internal energy of the saturated liquid, and (c) the (final) temperature? 3 kg. 30 m 100 kPa, 160°C 2 kg, 10 m 100 kPa, 140°C, 200 m/s 3 2 1 kg, 0 m 100 kPa. 100°C, i 1000 m/s ++ Q=9200 kJ mini= 10 kg 100 kPa, x=0.6 min= ? kg 100 kPa, Uin=? +7 kg, 20 m 4 100 kPa, 150°C 8 kg. 0 m 5 100 kPa. 130°C, 100 m/s
Carbon Dioxide is contained in a piston-cylinder assembly and undergoes a cycle made of the fol- lowing processes: • Process 1-2: Constant volume from 1 bar, 300 K to 600 K • Process 2–3: Polytropic expansion with n=k until P3 = P1 • Process 3-1: Isobaric compression (a) Sketch the cycle on p-v and T-v coordinates (b) Determine the work and heat transfer in each process, in kJ/kg (c) Determine the type of cycle that this is. If it is a power cycle, compute the thermal efficiency. Otherwise, compute the coefficient of performance for a heat pump cycle.
0.56 kg of water in a piston cylinder device as shown initially the water is at T, = 120 °C with volume V, = 36 L (State 1). Heat is then added such that all the water in the cylinder is saturated vapor and the piston just touched the spring without exerted any force on the spring (State 2). Then additional heat is added to the system such that the temperature is T, 600 °C and the pressure is P,= 400 kPa (State 3). 3 Po 3 1) Find the total work (from state 1 to state 3, in kW). O 147.73 2) O Not listed Qin 111.16 133.48 107 23 156.11 125.24 2) Find the total heat transfer for the process (from state 1 to state 3, in kW). 1424.6 O Not listed O 1486.0 O 1585.4
Air as an ideal gas is contained in a piston/cylinder system constrained by a non-linear spring. Initially the gas in the cylinder is at 100 kPa, which is balanced by the atmospheric pressure outside of the cylinder (the weight of the piston is negligible). The force on the spring at the start is zero. The spring force is F=kx². k=600. kNt/m². The cross-sectional area of the piston is 1 m², the initial volume is 1 m³, and the initial temperature is 300 K. Heat is added until the volume of the gas has expanded to 1.5 m³. Find: (a) The work done by the gas on the face of the piston (kJ). (b) The final temperature (K). (c) The amount of heat added (kJ). Hint: This problem is easiest if you calculate the spring work and the atmospheric work separately. Air V₁=1.0 m³ Piston Area = 1.0 m² T₁=300 K P₁=100 kPa Atmospheric P on upper piston face= 100 kPa
***Please show your correct and complete solution for this problem. Box your final answers and express in two decimal places. Sketch the schematic diagram.*** A rigid tank initially contains 5kg of saturated vapor steam at 150°C. Heat transfer is done until the pressure of steam reaches 1.20 MPa. Sketch the P-v diagram. Solve for the change in enthalpy and heat transferred.
Air in a rigid tank is at 200oC and 150 kPa. The air is cooled to a final equilibrium state of 60oC . i. Determine the change in pressure of the air, kPa. ii. Show and label the process on a temperature versus volume (P-v ) diagram. The gas constant for air, R is 0.287 kJ/kg.K and the universal gas constant, Ru is 8.314 kJ/kmol.K.
* Your answer is incorrect. Water contained in a piston-cylinder assembly, initially at 300°F, a quality of 80%, and a volume of 6 ft3, is heated at constant temperature to saturated vapor. If the rate of heat transfer is 0.3 Btu/s, determine the time, in min, for this process of the water to occur. Kinetic and potential energy effects are negligible. At = i 5.217 min
A piston-cylinder device contains an ideal gas of nitrogen. At the initial state, the volume is V1= 1.00 m3, the pressure is p1= 400.00 kPa, the temperature is T1= 300.00 K. An electric heater within the device is turned on for a time of Δt = 5.00 min. The current is I = 3.00 A, and the source voltage is V = 120.00 V. During the heating process, the gas expands, and a heat loss of Qout = 2.80 kJ occurs. The gas constant is R = 0.297 kPa·m3/(kg·K), and the room temperature specific heat at constant pressure is cp =1.039 kJ/(kg·K). Calculate the electrical work done on the gas, Wele__________ (kJ)