As shown in the figure, a 300-ft tank contains 25 Ib of H2O initially at 30 lbf/in?. The tank is connected to a large steam line carryingsteam at 200 lbf/in?, 450°F. Steam flows into the tank through a valve until the tank pressure reaches p2 = 140 lbf/in? and thetemperature is 400°F, at which time the valve is closed.Steam at200 Ibfin.?,450°FTankValve(1)Initially:30 Ibf in?, mi = 25 lb(2)Finally:P, Ibfin?, 400°FDetermine the amount of mass that enters the tank, in Ib, and the heat transfer to the tank from its surroundings, in Btu.

Answered: As shown in the figure, a 300-ft tank…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

One mole of a monoatomic, ideal gas goes through the cycle shown in thediagram. Paths AB and CD are isothermal, while paths BC and DA are isobaric.Find TA, TB, TC, and TD
A reheater cycle with two stages of reheating is executed with steam expanding initially from 20.356 Mpa and 540 oC. The pressures of two reheaters are 3.2356 Mpa and 0.85356 Mpa, and the steam leaves each reheater at 540oC. Condensation occurs at 70oC. Calculate W, ec and ee.
A pressure cooker has the lid screwed in tight. A small opening with A= 0.0075 in^2 is covered with a petcock that can be lifted to let steam escape. How much mass should the petcock have to allow boiling at 250 F with an outside atmosphere of 15 psia?
29. The work steady flow for an open system is 3.12 HP. During steady flow process, the of the working substance drops from 200 psia to 20 psia and the speed increases from 200 to pressure 1000 fps. The internel energy decreases 25 HTU and the specific volume increases from 1 to 8 Sketch the pV diagram and compute the heat in HP for 10 of the substance. min
A room is divided by a barrier into two sections. One side of the room (state 1) has a volume of 1000 ft^3 and is initially at 70F, 50 psi and the other side of the barrier (state 2) has 200 lbm of air and is initially at 300F, 14.696 psi. The divider is removed and the air mixes until it reaches equilibrium (state 3). Find the final temperature and pressure of the room. You can assume removing the divider has a negligible effect on the air.
H.W/ Steam at 10bar, 0.95dry is heated electrically at constant pressure process. If the rate of consume power is 1kW and the rate of steam is 0.3kg/min, determine the final state of steam?
How to do D and E
100kg of water at 75C and 1 bar is heated in a boiler to superheated steam at 5 bar and 350C. Calculate the change in internal energy O a. 200,100 kJ/s b. 98,221 kJ/s Oc. 67,763 kJ/s d. 256,910 kJ/s Clear my choice
None
QI/ A volume of the vessel A is 0.3 m contains ammonia at 25 °C, 90% Acaonia quality. The pressure of cylinder B will be floated at 200 kPa, cylinder B in the beginning is empty. The air is flowed into cylinder B when the valve is opened and reaches to equilibrium state of 200 kPa, 25 °C. Determine the heat transfer during the process.
Q1/ A volume of the vessel A is 0.5 m' contains saturated water at 275 °C, 80% quality. The pressure of cylinder B will be floated at 300 kPa, cylinder B in the beginning is empty. The air is flowed into cylinder B when the valve is opened and reaches to equilibrium state of 300 kPa, 275 °C. Determine the heat transfer during the process. S va
104#1. an ideal gas with R=0.062 BTU/lbm-degree R and Cv=0.158 BTU/lbm-degree R undergoes athree process cycle in a cklose system. from the initial state of 20 psia and 570degree R, the gas is compressed at coinstant pressure to 1/5 of its initial volume, process 1-2; it is then heated isochrocally to state 3, process 2-3; and finally, it expands polytopically with index n=1.5 back to its initial state, process 3-1. determine the pressure, specific volumes and temperatures at cardinal points around the cycle and the cycle thermal efficiency.

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS