As shown in the below figure, two blocks each weighing 1.5 kN are connected by a uniform horizontal bar which weighs 1.0 kN. If the angle of friction is 15° under each block, find P directed parallel to the 45° incline that will cause impending motion to the left.

As shown in the below figure, two blocks each weighing 1.5 kN are connected by a uniform horizontal bar which weighs 1.0 kN. If the angle of friction is 15° under each block, find P directed parallel to the 45° incline that will cause impending motion to the left.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

4 10 points A file cabinet weighing 215 lb is being pushed to the right with a horizontal force P applied a distance h from the floor. The width of the file cabinet is w = 15 in., its mass center G is a distance d = 2 ft above the floor, and static friction is insufficient to prevent slipping between the cabinet and the floor. The coefficient of kinetic friction between the cabinet and the floor is Uk = 0.28. Take the value of P to be 70 lb. 01 0!!! 01 Determine the maximum height ŉ at which the cabinet can be pushed so that it does not tip over, and find the corresponding acceleration of the cabinet. The maximum height at which the cabinet can be pushed so that it does not tip over is The acceleration of the cabinet is 1.466 ft/s². 1.7 x ft.
6. Determine the force F required to lift a 300 N load F, with each of the pulley systems shown in Figure below. Neglect friction and the weights of the pulleys.
A beam with a length of 2 m and a mass of 10 kg supports a 50 kg box. The beam is connected to a wall by a hinge at its base and a horizontal wire. The wire is connected to the beam 1.5 m from the hinge and makes an angle θ of 35o to the beam. The goal is to find the tension in the wire and the horizontal and vertical components of the force exerted by the hinge on the board Calculate the tension in the string. write down Newton’s 2nd law for both x and y directions. find the horizontal and vertical components of the force that the hinge exerts on the beam. Suppose the maximum tension that the wire can withstand is 1500 N. What is the maximum load that the hinge can support before the wire breaks?
The 60 kg two-wheeled cart is described in the figure and parameter table below, with G indicating the location of the center of gravity. It is to be pulled so that it goes up the small step. Find the normal force on each wheel, and the magnitude and direction of the force applied at handle. HINT: remember that there are two wheels sharing the load @080 BY NO SA 2021 Cathy Zupke 4₁1 G L₁ L₂ parameter value 0.6 0.5 0.8 0.7 0.2 A L3 LA d L3 units m m m m m B L₂ F For the answers, take to the right and up to be the positive directions. The normal force at each wheel at A in the x direction is Ax= 150 XN The magnitude of the force at B is F Measured from the positive horizontal axis, the angle of F= 45 X° = 212 XN
The uniform bar AB weighing 240 lb is mounted as shown in the figure upon a carriage weighing 480 lb. The center of gravity of the carriage is at C midway between the wheels. If P = 180 lb and there is no frictional resistance at the wheels, find the value of R1
Please asap
The pulley system shown in Figure Q1c lifts a mass,m,of 550 kg.Calculate the force FA necessary to maintain the suspended mass in static equilibrium; and determine the forces at the ceiling anchor points A and B. Assume frictionless and weightless pulleys and use g = 9.81 m/s2.
2 Your answer is partially correct. Try again. In the figure, a slab of mass m, = 40 kg rests on a frictionless floor, and a block of mass m, = 9 kg rests on top of the slab. Between block and slab, the coefficient of static friction is 0.60, and the coefficient of kinetic friction is 0.40. A horizontal force F of magnitude 102 N begins to pull directly on the block, as shown. In unit-vector notation, what are the resulting accelerations of (a) the block and (b) the slab? u = 0- (a) Number T-7.4 -7.4 Units m/s^2 (b) Number i+ Units m/s^2 -0.88 Click if you would like to Show Work for this question: Open Show Work SHOW HINT LINK TO TEXT LINK TO SAMPLE PROBLEM LINK TO SAMPLE PROBLEM VIDEO MINI-LECTURE 10:50 PM search ENG 4/4/2021 ond 111Pgup) pri sc DOUSE insert dele home break 13) 23 bac 3 5. 4 R.
Please reply as soon as posible, thanks! I don´t have much time:( Static Problem: The spool shown in the figure has a weight of WAB = 27,50 N, and its center of gravity is located at its geometric center O, the spool has a larger radius R=0,17 and an inner radius r=0,13, and it has a coiled rope. Block C has a uniform weight WC= 60 N. Consider the friction between block C and the top of the spool at A, between the spool and the surface at point B and between the rope and pulley D, the friction coefficients are respectively: μs@A=0,30, μs@B =0,45 and μs@D=0,35. The chord is parallel to the plane. Carry out: a) The free-body diagrams of the block and the reel. b) The calculation of the maximum value of P that can be applied without losing the equilibrium of the system.
A force of 1000 lb is applied to the 600-lb horizontal beam supported by a hinge at A and a roller at B on a smooth surface. If the pin support at A suddenly fails, calculate the magnitude of the force of the roller at B acting on the beam at that instant, by modelling the beam as a uniform slender bar. Present your answer in lb using 3 significant figures. 4 13 1000 lb -8 ft- B -2 ft-
Please don't provide handwritten solution ....
Please answer this within 30 mins! I will upvote !