As part of a check on its design, a lower A-arm (part of an automobile suspension) is supported by bear- ings at A and B and subjected to the pair of 900-N forces at C and D. The suspension spring, not shown for clarity, exerts a force Fs at E as shown, where E is in plane ABCD. Determine the magnitude Fs of the spring force and the magnitudes F, and Fg of the bearing forces at A and B which are perpendicu- lar to the hinge axis AB.

As part of a check on its design, a lower A-arm (part of an automobile suspension) is supported by bear- ings at A and B and subjected to the pair of 900-N forces at C and D. The suspension spring, not shown for clarity, exerts a force Fs at E as shown, where E is in plane ABCD. Determine the magnitude Fs of the spring force and the magnitudes F, and Fg of the bearing forces at A and B which are perpendicu- lar to the hinge axis AB.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

8. The 100 lb "slider" C is held in place on the smooth bar by the cable AC. Determine the tension in the cable and the force exerted on the slider by the bar. 7 ft 4 ft 6 ft 4 ft 4 ft. Figure: 03-18-074UNEX-Example 3.6 Application of the Dot Product (Related Problem 3.79) Contit300 Penn Practice
Determine the n- and t-components of the force F which is exerted by the rod AB on the crank OA. Evaluate your general expression for F = 118 N and (a) e = 30°, B = 25° and (b) e = 21°, B = 29° Answers: (a) Fn= i N, F: = i N (b) Fn = i N. F:= N
There are two parallel forces and two pure moments in the figure. What distance "d" must separate the forces in order for the system to be in equilibrium? F = 9 N, M1 = 15 N-m, M2 = 69 N-m, = 60 degrees, a = 1 m, b = 1 m, c = 2 m
FA K mm L mm- M mm The operation of the fuel pump for an automobile depends on the reciprocating action of the rocker arm ABC, which is pinned at B and is spring loaded at A and D. When the smooth cam C is in the position shown, determine the force acting on pin B along Y axis and input its absolute value. (If your answer is negative, input its positive value such as -17 --> 17) Use the followings; FA=57N FC=246N K=51mm M=12mm L=22mm O=35degrees
please make it clear and box the answer
The jib crane is designed for a maximum capacity of 6 kN, and its uniform I-beam has a mass of 190 kg. Plot the magnitude R of the force on the pin at A as a function of x through its operating range of x = 0.2 m to x = 3.8 m. On the same set of axes, plot the x- and y- components of the pin reaction at A. Do these plots on a separate piece of paper. Then answer the following questions in Wiley Plus as a check for your work. (a) What is the value of R when x = 1.6 m? (b) What is the value of R when x = 3.3 m? (c) Determine the minimum value of R and the corresponding value of x. (d) For what value of R should the pin at A be designed? 37° 6 KN 1.2 m 2.8 m Questions: (a) If x= 1.6 m, R= i (b) If x= 3.3 m, R= i (c) The minimum value for R = i (d) The pin should be designed to hold i kN kN kN at x = kN. i E
The jib crane is designed for a maximum capacity of 14 kN, and its uniform I-beam has a mass of 270 kg. Plot the magnitude R of the force on the pin at A as a function of x through its operating range of x = 0.2 m to x = 4.9 m. On the same set of axes, plot the x- and y- components of the pin reaction at A. Do these plots on a separate piece of paper. Then answer the following questions in Wiley Plus as a check for your work. (a) What is the value of R when x = 2.4 m? (b) What is the value of R when x = 4.5 m? (c) Determine the minimum value of R and the corresponding value of x. (d) For what value of R should the pin at A be designed? 1.6 m Questions: 25° 14 KN -3.5 m (a) If x = 2.4 m, R = (b) If x= 4.5 m, R= (c) The minimum value for R = i (d) The pin should be designed to hold i KN KN kN at x = i kN. m
Show steps Draw Free Body Diagram
The jib crane is designed for a maximum capacity of 14 kN, and its uniform I-beam has a mass of 270 kg. Plot the magnitude R of the force on the pin at A as a function of x through its operating range of x = 0.2 m to x = 4.0 m. On the same set of axes, plot the x- and y-components of the pin reaction at A. Do these plots on a separate piece of paper. Then answer the following questions in Wiley Plus as a check for your work. (You can disregard the plot, I only need a, b, c, and d)
Please include free body diagram. Don't make any mistakes
Boom OAB is supported by a ball and socket at point O and two cables AC and AD. Determine the forces supported by the two cables and the support reactions at O if P = 520 kN. 3m C 5m 3m 9m 5m i 6m B. 4m 12m 6m 5m
Problem 3. Determine the vertical clamping force at E in terms of the force F applied at the handle. E is in smooth contact with the ground. (Hint: Look for two-force members) a/2 h - 1.5 a |C 60 DE a/2' 1.5 a