BOOK - Principles of heating ventilating and air conditioning 17.12 A heat pipe air-to-air energy recovery device isbeing considered for a system requiring 9000 SCFM ofoutside air. Initially, a separate preheater was planned forbringing the outside air from its -2°F design ambientoutdoor temperature to 40°F. Determine:(a) the rating (Btu/h) and(b) the sensible effectiveness (%) to specify for the heatpipe unit if it is to eliminate the need for the air preheater.

Data we have v=9000 = cfm 9000 ft ³/min 9000(12 *0.0254)³/60 V = 4.2475 m³/sec W.K.T Density of…

Answered: arate preheater was p from its –2°F…

Engineering

Mechanical Engineering

arate preheater was p from its –2°F design

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: Discuss the reason to use “Engine Coolants” in engine cooling system.

A: Solution: Note: Dear Student! As per our guidelines! we are only allowed to answer a single…

Q: eat expulsion occurs in what section of a heat pump system when operating in the heat mode? A.…

A: Heat expulsion means removal of heat from the system,

Q: rop in the plumbing system

A: given: explain pressure drop in the plumbing system

Q: Unique characteristics of monoblock air conditioners in comparison to a split air conditioning…

A: Air conditioners are used to maintain the parameters of the air of some specific region. Various…

Q: Which one of the following statement is correct? * O evaporative cooling and sensible cooling is the…

A: Evaporative cooling is water evaporation through which the air is cooled down to a comfortable…

Q: Two types of heating profiles in thermal processing are ________ and

A: In case of thermal processing of food mainly two types of heating profiles are present.

Q: Why do all open cooling towers not have side stream filtration?

A: Cooling towers are an essential segment of numerous refrigeration frameworks, giving solace or…

Q: What are the considerations that should be done before the installation process of pipes in a plant?

A: The consideration are:1. The selection of the material is good. The material to be selected can bear…

Q: What is the difference between sandy plumbing and streamlined plumbing?

A: To find: The difference between sandy plumbing and streamline plumbing. Given: The two type of…

Q: The typical temperature difference between the enteringair and the boiling refrigerant on a standard…

A: The temperature split, sometimes referred to as the approach temperature, is the difference between…

Q: 3) The Ar handling unit is a part of. a. Central HVAC system. . b. Cooling part of central HVAC…

A: 3. The air handling unit is a part of a. Central HVAC system b. Cooling part of central HVAC system…

Q: What is the length of the finned section of pipe in this baseboard hot waterheating system?

A: Find Calculate the length of the finned section of the pipe

Q: Which part in the mechanical heat pump is used to increase the refrigerant pressure? Select one: a.…

A: Given Data : Mechanical heat pump

Q: Describe the following components of cooling load. Inside and outside design calculation, solar and…

A: Whenever a cooling system is designed for a specific space, calculations of the heating load are…

Q: (a) List out the classification of air-condition (b) With the aid of following sketch diagra details…

A: Air-Conditioning:- By removing the heat and moisture from an area, air conditioning (also known as…

Q: raphs and discussion : - What is the main benefit for the safety valve? What is the reason of…

Q: Explain the the fan design procedure?

A: Given Fan Design To find Design procedure of fan

Q: a) Explain four factors in determining the comfort level for an air conditioning room. Suggest the…

A: there are basically 4 functions of air conditioning. These are 1. temperature control 2. humidity…

Q: J - Type Thermocouple is the combination of _____________ and ________________ materials. a. Iron…

A: GIVEN DATA A FILL IN THE BLANK QUESTION GIVEN WE HAVE TO FILL APPROPRIATE OPTION

Q: n of refrigeration me

A: given: one ton of refrigeration means?

Q: What are some criteria that need to be considered in the selection of a refrigerant? Please choose…

Q: Multi-evaporator systems are When the required temperature lift is small When the required…

A: Multi evaporator system is used when maintain different temperatures at different point. Widely used…

Q: me in and com mps and valve w and return

A: In central heating system two types of pipes are used,

Q: The approach temperature for the evaporator isA. the difference between the suction and head…

A: The condenser approach temperature can be simply defined as the difference in temperature that…

Q: Which of the following material have highet Heat Storage capacity ON Aluminum O b. Wood O c. Brass O…

A: The heat storage capacity may be defined as the heat stored in a material. To compare the heat…

Q: Which process would best represent the opposite ofexhausting air from a system?A. CoolingB.…

A: Given Data : Exhausting air

Q: Describe primary and secondary heat exchanger

A: A heat exchanger is a system used to transfer heat between two or more fluids. Heat exchangers…

Q: Which device can be used to recover waste heat from flue gas? a. flue gas recoverer b. boiler…

A: Feed water economizer is the correct answer

Q: Which of the following is true regarding the refrigerantpiping on a rooftop package unit?A. The…

A: The rooftop package unit is a type of system in that all components that necessary for conditioned…

Q: Air-condition system being in every organization. How the Maintenance of Air Conditioning System…

Q: Refrigerant works by absorbing ____ from the environment where cooling is required

A: As the refrigerant absorbs heat from indoor air, it transitions from a low-pressure gas to a…

Q: GIVE THE JOB OR OPERATION WHERE HIGH AIR HUMIDITY IS PRESENT

A: Humidity is the concentration of water vapor in the air. water vapor in the gaseous form is…

Q: When using a time-cycled/ pressure-limited ventilator, what will happen when the preset time limit…

A: Time-cycled/ pressure-limited ventilator is a kind of mechanical ventilator used for respiratory…

Q: Explain in detail what is the Feed and the Product streams for Mechanical Draft Cooling Tower

Q: When assembling refrigerant lines on the job, the tubing should be kept _______. Select the answer…

A: Given When assembling refrigerant lines on the job, the tubing should be kept _______.

Q: 10. A crankcase heater is used to warm a compressor to prevent the condensing of A. moisture inside…

A: It is required to choose correct option

Q: The contact factor for a heating coil-36

A: The contact factor of heating is coil can be determined by the efficiency for dehumidification. The…

Q: How is the selection of coolant done in condensing systems?

A: Coolant : Coolant is a substance which is used to remove or extract the heat from the parts which is…

Q: List seven advantages that an aluminum parallel- flow,plate/fin evaporator has over a standard…

A: The function of the Evaporator (in the refrigeration system) is to absorb heat into the system from…

Q: The outside design temperatures in the summer inTucson, Arizona, for 2.5% of the time are _________…

A: Summer Design Temperature @ 2.5% : The outside design temperatures for summer in Tuscon, Arizona,…

Concept explainers

Hydronics

Question

BOOK - Principles of heating ventilating and air conditioning

17.12 A heat pipe air-to-air energy recovery device is
being considered for a system requiring 9000 SCFM of
outside air. Initially, a separate preheater was planned for
bringing the outside air from its -2°F design ambient
outdoor temperature to 40°F. Determine:
(a) the rating (Btu/h) and
(b) the sensible effectiveness (%) to specify for the heat
pipe unit if it is to eliminate the need for the air preheater.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Write down details about Cooling Tower's working principle, components and description with diagrams.
Describe the components of a solar heater.
Describe a direct-expansion versus a flooded evaporator.
What is the total length of this furnace and air-conditioning system?
Show and explain a typical chilled water central air conditioning system.
Explain the principle behind indirect fired heater ?
Which of the following components is NOT a type of ventilation system? Select one: a. Airconditioning Units b. Venting Skylight c. Boilers d. Exhaust Fans
What recommendation would you suggest for improving the performance of the ground-source heat pump
Which is the safest distance between the wall and the boiler? a. 5m b. 1.5m c. 1m d. 10m
In the induced draft cooling tower, the fan forces the air through the tower. True False
1- What is the pressure at the Economizer (in bar)? 2- What is the pressure at the Evaporator (in bar)? 3- How much heat received by the Economizer (kW)? 4- How much heat received by the Evaporator (kW)? 5- How much heat received by the Superheater (kW)? 6- How much heat received by the FWH (KW)?.. 7- How much heat received from the fuel burning (kW)? 8- How much heat rejected at the chimney (kW)?. T=35 C From the Pump m-1.3 kg/s + Cpw=4.2 kJ/kg.C ****************** T=150 C, To the Turbine Cp 1.008kJ/kg.K T=400C 44 T=212.2 X=0.0 X=0.85 Chimney Hoo bou to Economizer Evaporator Super Heater -Air, m-4 kg/s, T=20 C P=5 bar, X=0.8, m=0.3 kg/s from FWH X=1 1 Fuel, T-20 C, m=0.2 kg/s, C.V=33.5 MJ/kg Bumer