Answer the question in the below image. A three phase star-star transformer has a rating of 30MVA, 230/69 kV with a leakage reactance of 10%. Choosing a base of 30 MVA and 230kV on high voltage side, the transformer reactance referred to the low voltage side will be (ohms). O 157.8 Q 15.87 Q O 176.33 Q O17.67 Q

Q: A transformer has a rated output of 400 kVA at a power factor of 0.6. Determine the rated power…

A:

Q: In transformer, the hysteresis loss depends on load current O only flux density O both frequency and…

A: consider the given question;

Q: A transformer has a rated output of 400 kVA at a power factor of 0.6. Determine the rated power…

A: As per the question, it is given that Rated output (S) = 300 kVA Power factor (ϕ) = 0.6 We have to…

Q: To improve the load power factor, a Delta-Connected capacitor bank is connected on the low voltage…

A:

Q: A transformer has a rated output of 300 kVA at a power factor of 1.2. Determine the rated power…

A: Please comment if you need any clarification. If you find my answer useful please put thumbs up.…

Q: Ql-phase step down transformer 1250 KVA, 11000/2200 V, 50 Hz . The resistance /phase and leakage…

A: (i) The per-phase secondary voltage in the star-connected secondary winding can be calculated as,

Q: Problem: For the given circuit as shown in figure a) Find the equivalent reactance b) Draw the…

A: Solution !!

Q: A transformer has a rated output of 300 kVA at a power factor of 0.6. Determine the rated power…

A: As per the question, it is given that Rated output (S) = 300 kVA Power factor ϕ= 0.6 We have to find…

Q: Consider a single phase transformer with primary and secondary turns of 1000 and 200 respectively…

A: Given:R1=10.5ΩR2=2.5ΩX1=12.5ΩX2=2.5ΩRm=15.55KΩXm=10KΩK=1000200=5

Q: I will upvote for correct answer A transformer has a rated output of 300 kVA at a power factor of…

A:

Q: A 2.2 KVA, 480/4800-V, 50 Hz, single-phase transformer is tested with the following results. Find…

A:

Q: mer has primary and 80 turns on the secondary. The primary 2. A 100 KVA transf and secondary…

A: Given data, The rating is 100kVA. Primary resistance  = 0.3Ω Secondary resistance  = 0.1Ω Primary…

Q: VA rms() IA LA) PA (W) QAVAR (rad ts) (rod is)

A: Since you have posted a question with multiple sub-parts, We will solve the first three parts for…

Q: A transformer has an input voltage of 2kV and a step-down ratio of 5:1. The primary and secondary…

A: According to question: The equivalent resistance with respect to secondary winding is calculated as…

Q: transformer has a rated output of 200 kVA at a power factor of 0.6. Determine the rated power output…

A:

Q: For the following circuit if the secondary voltage of the transformer is 20V rms, the PIV of the…

A:

Q: 5. Convert the Octal number (453.47)8 to decimal number.

A: As per bartleby expert policy, only one individual question is to be answered. Kindly repost…

Q: Consider the circuit in the figure below: a) What are the benefites of using the transformer in this…

A: Cut in voltage of silicon diode is 0.7V and cut in voltage of germanium diode is 0.3V. During…

Q: the cross over frequency of the system with transformer function k[s+1]/s2 and phase margin equal to…

A: In this question,  We need to calculate the the cross over frequency of the system with transformer…

Q: The primary induced EMF (E1) is 180 degrees out of phase with V1 but the equal magnitude in the…

A: The primary induced EMF (E1) is 180 degrees out of phase with V1 but the equal magnitude in the…

Q: In a single phase transformer, if the average value of emf is 239 V, then RMS value is

A:

Q: If the open circuit voltage is 225V and the full load voltage is 214V, then the percentage…

A: Percentage regulation is given by R    R = (VOC - VFL ) / VFL    VOC = Open circuit voltage    VFL =…

Q: A single-phase transformer has a voltage ratio on open circuit of 7900/660 V. The primary and…

A: Transformer: It is a static device that is used to step up and step down the voltages.

Q: A parallel connection of a RL branch with a C branch is connected across a 100V AC mains. At first R…

A: In RL parallel connection branch resistor and inductor are connected in parallel with each other and…

Q: In no load Phasor diagram of practical transformer, the core loss current Ic is with primary voltage…

A: When a transformer is on no-load, the secondary is open circuited. Hence secondary current is zero.…

Q: O What are the 'ideal transformer' secondary and primary voltages Ez and E, and source voltage V1?

A:

Q: In a single phase transformer, when no-load voltage is 230V and full load terminal voltage is 220,…

A:

Q: Q/A single-phase transformer with a capacity of 100 kVA and a voltage of 2000/400 and the equivalent…

A:

Q: A 5KVA, 240/120 V single phase transformer has the following parameters R1 = 0.06 Q R2 = 0.015 Q X1…

A: 5kVA, 240/120V Single phase transformer has given parameters.  Find the primary current, voltage…

Q: Solve it quickly please

A: From the above problem we have given  Hence symmetrical component of voltage is given as

Q: Ql-phase step down transformer 1250 KVA, 1 1000/2200 V, 50 Hz .The resistance /phase and leakage…

A:

Q: If the no load secondary voltage of a 1-phase transformer is 233 V and fullI load secondary voltage…

A:

Q: A current transformer has a phase error of +3°. The phase angle between the primary and secondary…

A: Given: A current transformer has, Phase error = +3°

Q: Ql-phase step down transformer 1250 KVA, 11000/2200 V, 50 Hz .The resistance /phase and leakage…

A:

Q: Determine the peak-to-peak ripple and dc output voltages. The transformer has a 36 Vrms secondary…

A: Given, RMS voltage at the secondary side of the transformer, Vs=36 V Supply frequency, f=60 Hz…

Q: For a 250 [kVA] practical transformer with 4160 [V) primary and 480 [V] secondary, the base…

A:

Q: Ql-phase step down transformer 1250 KVA, 11000/2200 V, 50 Hz .The resistance /phase and leakage…

A:

Q: In small transformers, the total iron losses may vary from % of the rated output. O 0.5 to 1 O 0.2…

A: They can either be graphite or precious metal brushes which have electrical motor connections. To…

Q: In no load phasor diagram of practical transformer, the magnetizing current is with primary voltage…

A:

Q: A multitap transformer has 1500 turns on the primary, 100 turns between B and C, 600 turns between A…

A:

Q: A three phase power transformer having a line voltage ratio of 400 V to 33 kV is connected in…

A: We have an three-phase power transformer as shown in figure, Voltage ratio = 400 V / 33 KV Current…

Q: For the given circuit below, a step down transformer gives an RMS voltage of 230 V/ 16.7-0- 16.7 V…

A: Given, RMS voltage = 230V/16.7-0-16.7 V load resistance = 2.2 kilo-ohm

Q: A transformer has 520 primary turns and 160 secondary turns. The primary and secondary resistances…

A: First we will refer secondary side resistance and reactance to primary side and than we will find…

Q: The table below shows some performance parameters of a certain power transformer. Full-load voltage…

A: The voltage regulator is required to maintain voltages within the permitted range that the…

Q: Given three phase fullwave with center tapped transformer with 220 Vac source voltage, determine:…

A: Since you have posted a question with multiple sub-parts, we will solve the first three subparts for…

Q: Problem: The rating of three phases of a 3 winding transformer are: Primary Y-connected: 15MVA,66KV…

A: Consider the base values are given as: 30 MVA, 70 kV Since the base voltage for the primary winding…

Distribution System

The final stage in the delivery of the electric power is the electric power distribution system. From the transmission system to the individual customers it carries electricity. The distribution system is connected with the transmission system and is used to lower the voltage of the transmission to medium voltage in the range of 2 kV to 35 kV with the help of transformers. This medium voltage to the distribution transformers located near the customer's premises is carried by the primary distribution system lines. These distribution transformers in turn lower the voltage to utilization voltage used in lightings, household appliances, industrial equipments etc. Through secondary distribution lines often several customers are supplied from one transformer. It is through service drops, the commercial and residential customers are connected to the secondary distribution system lines. Customers who demand a larger amount of power can be connected directly to the primary distribution system level or the sub-transmission level.