Answer the following: 1. Identify the design speed, minimum surface, outside shoulder, and paved shoulder slope for the following specification of the road: a. A local road in urban area with 180 ADT b. A collector roadway in rural area, mountainous, and with 580 ADT c. A local road in rural area, rolling terrain and with 420 ADT

Answer the following: 1. Identify the design speed, minimum surface, outside shoulder, and paved shoulder slope for the following specification of the road: a. A local road in urban area with 180 ADT b. A collector roadway in rural area, mountainous, and with 580 ADT c. A local road in rural area, rolling terrain and with 420 ADT

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A long segment of suburban freeway is to be designed on level terrain. The level segment, however, is followed by a 4.5% grade, 2.0 miles in length. If the DDHV is 2,500 vehicles per hour with 15% trucks (standard mix), how many lanes will be needed on the (A.) Upgrade, (B.) Downgrade, (C.) Level terrain segment to provide for level of service C? Lane widths and lateral clearances may be assumed to be 12 feet and 6 feet, respectively. Ramp density is expected to be 1.0 ramps per mile. The PHF is 0.92. Good weather, no incidents, no work zones, and regular users of the facility may be assumed.
the minimum tangent runout distance for a four lane road with a 6% full superelevation and a speed limit of 45 mph is ____ft
What is the safe stopping distance for the rural freeway section with design speed 80 miles/hour at 4% incline?
Determine the minimum sight distance for a two-lane divided Highway in hilly terrain on a 4% descending grade. data as per IRC recommendations given are V=60kmph, f=0.36, t=2.5sec.
2. Calculate the total stopping sight distance for a wet pavement condition, if the design speed is 100 Km/hr for the following three conditions. a. Road is flat b. The road has a 6% downslope c. The road has a 3% upslope
Determine the value of PTSF for a 6-mile two-lane highway in rolling terrain. Traffic data are as follows: • Volume = 1600 veh/h (two-way) • Percent trucks = 14% • Percent RVs = 4% • Peak hour factor = 0.95 • Percent directional split = 50 - 50 • Percent no-passing zones = 50
Two low-volume two-lane streets (lane width = 11 ft) intersect in an urban residential area at 120-60 degree-angle. Recommend appropriate curb configurations for this intersection based on AASHTO (2011) recommendations for a passenger car design vehicle. Draw a neat sketch for the intersection showing the dimensions of all elements you selected in your design.
Problem 2. New freeway is being designed on a level terrain, free-flow speed 70 mph 12-ft lanes, 6-ft lateral clearance Peak hour volume 2700 veh, 12% heavy vehicles PHF = 0.92 FIND: Number of lanes for LOS C
Design speed of a six-lane undivided highway is 70 mph. A circular section of the highway has level grade, 10-ft wide lane, and the radius of the highway centerline is 1000 ft. Calculate the minimum side clearance required from the edge of the innermost lane on the highway to provide adequate sight distance for safe travel
6.14 A freeway segment currently has four 11-ft wide lanes and a 3-ft right shoulder in the southbound direction. It is operating in LOS B with a traffic density of 15.6 pc/mi/ln and a peak-hour factor of 0.85. The freeway is on level terrain with 15% heavy vehicles, and currently has no on- or off- ramps within a distance of three miles upstream and downstream of the mid-point of the analysis section. New interchanges are to be constructed that would result in 6 on- and off-ramps within the distance of three miles upstream and downstream of the mid- point of the analysis section and total traffic volume is projected to double, with the same percentage of heavy vehicles, and the peak-hour factor going to 0.95. What would the new LOS and density be after the interchange construction and new traffic conditions?
A 3.25-mile segment of undivided, four-lane highway is primarily on level terrain. The highway segment does, however, contain one sustained grade of 2.5% that is 3,200 ft long. Other relevant information include: Base free-flow speed = 65 mph %3! 11-ft lanes • 4 ft clearance at the roadside (right side) • 20 access points/mile Peak-hour volume = 1,900 veh/h 13% trucks; 2% RVs • PHF = 0.90 • Familiar facility users At what LOS is the highway expected to operate? (Hint: Three different analyses will be needed: a) the level terrain portion of the highway, b) the 2.5% upgrade portion of the highway, and c) the 2.5% downgrade portion of the highway.)
6. A subdivision road is entering a public road. There is a stop sign before entering the public road. The reaction time is 2.5 seconds. The friction factor is 0.3. What the triangle dimensions that will define the clear sight triangle easement. Grade Speed % mph 3.0 20 Subom Rd 2. 3.5 25 3 4.0 40 4 4.5 30 1.0 35 2.0 40 7. 1.5 35 8. 2.5 55 9. 3.0 20 10 3.5 40 11 1.0 30 12 1.5 35 13 3.0 40 14 2.5 30 m2.