Answer by true or false then correct the false statement1- The min. reinforcement for column members is 0.001.2- The circular column is more ductile and most common using than non-circular one.3- When (e) greater than (es) then the compression failure occurs.4- Most common formula to calculate the spacing between ties is 48 times omain bar diameter5- The spacing between spirals is 25-55 mm6- The min. bar diameter of ties is 12 mm7- The dimension (h) of column taken along the eccentricity of load.8- When the directions of moments are the same, then the single curvature occurs.9- The crushing of concrete is the failure mode of all columns10- The min. no. of main steel reinforcement is 5 at circulars columns

Note : As per our guidelines we are allowed to solve 1 st 3 questions only. Please re - post the…

Answer by true or false then correct the false statement 1- The min. reinforcement for column members is 0.001. 2- The circular column is more ductile and most common using than non-circular one. 3- When (e) greater than (es) then the compression failure occurs.

Answer by true or false then correct the false statement 1- The min. reinforcement for column members is 0.001. 2- The circular column is more ductile and most common using than non-circular one. 3- When (e) greater than (es) then the compression failure occurs.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

i need the answer quickly
Hide bla Clear my choice A rigid beam is supported by a pin at A and two metallic wires at B and C. Determine the force P that causes the point C to displace downward by 0.3 mm. Given: E (wire B) = 70 Gpa, E (wire C) = 200 Gpa and both wires have a diameter D = 4 mm. Consider a linear elastic behavior. |-1 2 m 1.5 m A 3 m 2 m 2 m Select one: 11:49 PM A G d) ENG B
For the beam with coordinate shown in figure. Develop the flexibility matrix. 1 L 2 C 12 B
A short column constructed of a 254 x 254 x107 kg UC section (use the table below) is subjected to a compressive load P = 130 kN that has its line of action at one of the outside corners of the cross section (see figure).Determine the equation of the neutral axis under these loading conditions and Find the maximum tensile and compressive stresses σt and σc respectively, in the column.
pls help! Write the complete solutions and legibly. Answer in 2 decimal places. UPVOTE WILL BE GIVEN! MECHANICS OF DEFORMABLE BODIES Let Q = 0 and T = 8 (Example: 12Q°C = 120°C). Just substitute the number in letter. Thank you! For the frame shown, a 4QQT-N load is acting on member ABD at D. If the allowable material shear stress for is 4Q MPa, determine the required diameter (rounded off to the nearest 2.5 mm) of the pins at C and D. Pin C and pin D are subjected to double shear and single shear, respectively. If the thickness of member BC is 12 mm and that of member DE is 16 mm, determine the maximum bearing stress at C.
Identify the equation for the deflection at point C.
DETERMINE THE FORCE (Ib) IN MEMBER AB OF THE ROOF TRUSS SHOWN GIVEN THE DATA BELOW: F1=61 lb F2- 167 lb 0- 29 degree a 45 degree "Note: for compression, include.a negative sign (-) and for tension, type your answer as is. Input your answer in two (2) decimal places only without the unit. F1 C a D a A
Solution pls
A short rectangular column 500 mm on one side and 800 mm on the other side. It is reinfroced with 10-28 mm diameter longitudinal bars equally distributed to the shorter sides of the column. The centroid of the bars are 76 mm from the concrete surface. Use f'c = 28 MPa and fy = 415 MPa. NSCP 2015 requires α = cβ1 where β1 = 0.85 if f'c < = 28 MPa and β1 = 0.8 - (0.05/7)(f'c - 28) otherwise. Determine the following at balanced strain condition if the reduction factor is 0.65: Distance of neutral axis from concrete compression fiber in mm Design Axial Strength in kN Design Moment Strength in kN-m
Hand written please
Determine the member stresses in members AB, AC, AD, BC, and BD if the cross-sectional area for all members is 800 mm². Note: You may use any method 3 m ון 2 - 3 m 4 m 5 m 6 kN Situation 4: Terminologies 1. A structural element that carries a load that is applied transverse (perpendicular) to its length and the top fibers are in compression; the bottom fibers are in tension. 2. A structural element that is composed of smaller structural members typically configured in triangular arrangements. 3. Codes that specify combinations of loads that must be considered in the design of structures in the Philippines? 4. How many equations of equilibrium are there in space structures? 5. These are the forces exerted by supports on the structure and tend to prevent its motion and keep it in equilibrium. 6. The internal force in the direction of or parallel to the centroidal axis of the beam 7. The internal force in the direction perpendicular to the centroidal axis
DETERMINE FORCE (N) OF MEMBER EG in the truss shown. F1 = 214 N %D F2 = 876 N %3D F3 = 435 N a = 38 degree X = 15 m. **Note: for compression, include a negative sign (- ) and for tension, type your answer as is. Input your answer in two (2) decimal places only without the unit. В H A C E G F1 F2 F3