Researchers at UT Austin noticed that the seagrass beds in Corpus Cristi Bay (CCB)were taller and thicker than those in Lower Laguna Madre (LLM). They compared thesediment ammonium concentration, in the two locations. Following are the summarystatistics on sediment ammonium concentration, in micromoles, obtained by theresearchers. Equality of variances is not assumed.CCB: X₁115.1, s₁= 79.4, n₁ = 51LLM: X₂ = 24.3, S₂ 10.5, n₂: 19=a. At the 1% significance level, is there sufficient evidence to conclude that the meansediment ammonium concentration in CCB exceeds that in LLM?b. Determine a 98% confidence interval for the difference μ1-µ2, between the meansediment ammonium concentrations in CCB and LLM. Interpret your answer in (a)in words.c. Do the results in (a) and (b) provide the consistent results? Explain.

Given, For CCB sample size (n1) = 51 sample mean (x̄1) = 115.1 sample standard deviation (s1) = 79.4…

Answered: and thicker than those in Lower Laguna…

MATLAB: An Introduction with Applications

6th Edition

ISBN:9781119256830

Author:Amos Gilat

Publisher:Amos Gilat

Chapter1: Starting With Matlab

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

At ? = 0.10, can it be concluded that there is a difference in means of time spendfor studying between male and female based on point estimate in 2nd attached image?Assume the population variances are unequal
You are doing a one way analysis of variance on the fuel consumption of different makes of cars. You measure the fuel consumption of 93 cars in total. The number of car makes is 10 for this experiment. The sum of squares total is 192.40 and the sum of squares errors is 56.45. Find the sum of squares treatment correct to 2 decimal places.
onstruct a bimodal sample (with at least two different values in the set) of 5 measurements whose median is −3. If this is not possible, indicate "Cannot create sample".
Find the variance of the time to failure for two identical units, each with a failure rate 2, placed in standby parallel configuration. Compare the result with the vari- ance of the same two units placed in active parallel configuration. Ignore switch- ing failures and failures in the standby mode.
help me to do ii, iii, iv & v only
A company makes high-definition televisions and does not like to have defective pixels. Historically,the mean number of defective pixels in a TV is 20. An engineer is hired to make better TV’s that havefewer defective pixels. After his first week of work he claims that he can significantly improve the currentmethod. To check his claim you try his new method on 100 new televisions. The average number ofdefective pixels in those 100 TV’s is 19.1. Assume that the new method doesn’t change the standarddeviation of defective pixels, which has always been 4.(a) Test if the new method is significantly better than the old one at the α = 0.05 level.(b) Using the new method, assume that the mean number of defective pixels is actually 19. What is thechance that your test from part 1 will conclude that the new method is statistically more effective?
The Precision Machining Company makes hand-held tools on an assembly line that produces one product every minute. On one of the products, the critical quality dimension is the diameter (measured in thousandths of an inch) of a hole bored in one of the assemblies. Management wants to detect any shift in the process average diameter from 0.010 in. Management considers the variance in the process to be in control. Historically, the average range has been 0.002 in., regardless of the process average. Design an x-chart to control this process, with a center line at 0.010 in. and the control limits set at three sigmas from the center line. Management provided the results of 80 minutes of output from the production line, as shown in the table below. During these 80 minutes, the process average changed once. All measurements are in thousandths of an inch. Sample data for Precision Machining Company Diameter (thousandths of an inch) Minutes 1- 12 10 11 13 11 12 10 9. 8 11 12 13 - 24 10 11 12 11…
Mr Sharma wants to assess if the time taken to complete a job by 3 different machines is significantly different at 5%. As he thought the worker may also impact the time taken hence he used 4 different workers and randomly assigned them to machine and jobs such that each worker works on each machine. State the hypothesis for Mr Sharma. Complete the table below and help Mr Sharma get the answer of the questions). Source of Sum of Squares Degrees of freedom Mean Square F Ratio Variation Between Workers 138.667 Between Machines 11.08 Residual Errors Total 166.667
The table next to this contains data on the duration of recovery time for 3 brands of headache medicine given to 15 fever patients with a temperature of 38°C or higher. Use One way Anova analysis and testing at a significance level of 0.05 to determine whether the mean duration of recovery caused by the three brands of medicine is the same or different
Experience has shown that a grade in MAT 2371 is normally distributed with mean 66 and variance 64. Assume that the grades are independent of each other. What proportion of the class will get a grade of at least 80? 0,5656 0.0401 0.5871 0.9599 0.4129
The engineer of large manufacturing company takes many measurements of a specific dimension of components from the production line. She finds that the distribution of dimensions is approximately normal, with a mean of 3.33 cm and a coefficient of variation of 3.60%. i. What percentage of measurements will be less than 3.50 cm? What percentage of dimensions will be between 3.10 cm and 3.50 cm? What percentage of measurements will be equal to 3.50 cm? What value of the dimension will be exceeded by 90% of the components? ii. iii. iv.
Can you please give me two sets of data where the shape distribution is different but the boxplot is identical?

SEE MORE QUESTIONS

Recommended textbooks for you

MATLAB: An Introduction with Applications

Statistics

ISBN:

9781119256830

Author:

Amos Gilat

Publisher:

John Wiley & Sons Inc

Probability and Statistics for Engineering and th…

Statistics

ISBN:

9781305251809

Author:

Jay L. Devore

Publisher:

Cengage Learning

Statistics for The Behavioral Sciences (MindTap C…

Statistics

ISBN:

9781305504912

Author:

Frederick J Gravetter, Larry B. Wallnau

Publisher:

Cengage Learning

MATLAB: An Introduction with Applications

Statistics

ISBN:

9781119256830

Author:

Amos Gilat

Publisher:

John Wiley & Sons Inc

Probability and Statistics for Engineering and th…

Statistics

ISBN:

9781305251809

Author:

Jay L. Devore

Publisher:

Cengage Learning

Statistics for The Behavioral Sciences (MindTap C…

Statistics

ISBN:

9781305504912

Author:

Frederick J Gravetter, Larry B. Wallnau

Publisher:

Cengage Learning

Elementary Statistics: Picturing the World (7th E…

Statistics

ISBN:

9780134683416

Author:

Ron Larson, Betsy Farber

Publisher:

PEARSON

The Basic Practice of Statistics

Statistics

ISBN:

9781319042578

Author:

David S. Moore, William I. Notz, Michael A. Fligner

Publisher:

W. H. Freeman

Introduction to the Practice of Statistics

Statistics

ISBN:

9781319013387

Author:

David S. Moore, George P. McCabe, Bruce A. Craig

Publisher:

W. H. Freeman

SEE MORE TEXTBOOKS

and thicker than those in Lower Laguna Mac ammonium concentration, in the two locations on sediment ammonium concentration, in o Equality of variances is not ass pou