& Compute and Draw as axial force, Shear force and bending moment of the following Portal frames? (2 30KN Hokalm kkkkkk 3m 3.6m 50KN 8m 9m 160KN 8m 4m A ung

Q: Using Method of Sections find 10 kips A 20′ – 0" F B 20'-0" 40 k G

A:

Q: 4. Considering sag rods and tie rods at midspan, what is the required diameter of sag rods in mm?…

A: Given;Fy = 248 MPaC10X20 properties: w = 29.76kg/mA = 3787.09 mm2 Ix = 32.84x106 mm4Iy = 1.17x106…

Q: Using Method of Joints determine the force in member EK. Hint: What is going on at N or H? 15 kips…

A: An overhanging truss with concentrated loads are given.Point I is supported by hinged support and…

Q: Find the Force in Pin C: A 10k 3' 5' C B 6k 3' 8'

A: Given:- To find:- Force at C

Q: using portal method, what is the axial force of column AB?

A:

Q: 3,6 m 2.7 m 2400 N B C D 2.7 m 1.5 m F E 4.8 m

A:

Q: Calculate the forces in all members of the trusses shown using the method of joints.

A: The given truss is To find:- All member forces Concept:- The method of joints is a technique used…

Q: The free-body diagram of the entire truss is shown. Find the force ly. I, M K C D E F A, L. L. L L.…

A: Find value of Iy,force in members CD,CJ and DJ

Q: 1x / G 2 16' 8 4² Internal Hinge Draw axial force diagram, shear force diagram and bending moment…

A:

Q: Draw the SFD and BMD for the beam? 200men mm. en man 123KN

A: For SFD (V) and BMD (M) first we have to calculate Reaction at both support

Q: The internal normal force in kN at point C is mostly near

A:

Q: Draw the shear diagram for the compound beam which is pin connected at B. Click on "add vertical…

A: Given : Draw the shear diagram of given figure below :

Q: 10 kN/m B 3 m 20 KN to C 10 m 3 m 1 D

A:

Q: 7) Find the bar forces for the bars marked with an "X". 32 B,

A: Given Data -

Q: Pb4 The crane weighs 8 tons with center of gravity at G and is held in place by the pin connection…

A: Given :

Q: A PL 13 X 140 A36 steel plate is connected to a gusset plate using M19bolts. Determine the design…

A:

Q: - Beam - Column

A: The The beam and columns are I section which are used.   Because of torsion , distortion both in…

Q: 60 mm 60 min 60 mm w 200 mm 6.3 Three boards are nailed together to form a beam shown, which is…

A: s = 75 mm  Fnail = 400 N  w = 120 mm

Q: Draw the FBD of each section 2.) Compute the bar forces up to member U3L3 3.) Get the Length, Bar…

A: Answer  Since the given truss is loaded symmetrically we get equal reactions RAV =RBV = Total…

Q: CS X 13.7 S10 × 25,4 PROBLEM 6.7 A columm is fabricated by connecting the rolled-steel members shown…

A: Given data - Shear force = 30 kips Space (S) = 5 in Diameter = 3/4 in Find out - Shearing stress in…

Q: lre the method of Uirtuat work to determine the vertical duplacement Of Joints B and D af the Jteel…

A: Using the unit load method: Deflection DB/D=mML/AE Where, m=Force in member due to the unit load M=…

Q: The Built Up Beam shown is made by connecting two channel shapes and two plates, using 0.75"…

A: Draw the schematic diagram for the beam as follows:

Q: Calculate horizontal deflection at support D for the given truss with applied loading. EA is…

A:

Q: •3. Draw the shear and moment diaoram, and determine the max shear and maximum moment. 30 kN/m OD 3m…

A: A loaded simply supported  beam is given in the question and it has been asked to determine and draw…

Q: W=100PLF7 CBEM 2 2A'

A:

Q: 4. Clearly show and dimension the tributary area of Beam 2. (Feel free to print or redraw the…

A:

Q: L & Beam AB ~ Wall b Shear release اسم spring SA, S₂ = ? B k = 48 EI L³

A:

Q: 5.14 Calculate the forces in the members of the truss shown using the method of joints. A 2 kips B E…

A:

Q: What is value of L or length to get the results of 8.68kn.m and 0.753 kn.m in the green box…

A: Here, it is given a roof truss design based on biaxial -bending. The question has asked What is…

Q: Draw Shear & Moment Diagrams A * 3' 3' 9k 6' B 3' 3k

A:

Q: -for the beam calculate the max bending and shearing stresses 3D 440 50fim 20 +2m+ 307 iy +300 4m…

A: Introduction : Maximum bending : When the shear force at that section is zero or changes sign, the…

Q: the design block shear strength (kN)

A:

Q: Determine the rorce in bars BD, CD, and DF of the Nacelle truss shown below. 600lb , 1200lb 1200b…

A: Trusses are structures made up of two members of equal strength. Two-force members are structures…

Q: 7) Find the bar forces for the bars marked with an "X".

A: Given :

Q: The internal normal force in kN at point D is mostly near

A: Let FBC be the force in BC.

Q: Determine the member forces for all members in the truss shown using the method of joints. Remember…

A:

Q: Analyze the given frame using Portal Method. Н G 3 k 15 ft D E F 4 k- 15 ft A В C 18 ft- 20 ft

A: Given data in question  Lateral loading  Span member length  To find out  Analyze frame using Portal…

Q: 3. By using section method, calculate the force member of CE, DE, DF and FE of the given truss. 3m…

A: Consider the moments about A as follows:

Q: Determine the 2nd moment of inertia, shearing force in each bolt, and average shearing stress in the…

A:

Q: Identify all zero-force members (you do not need to solve for member forces). d b 10' P 10 h j k m…

A:

Q: Determine the force acting on members DE, DC, BC in an inverted roof truss as shown below. Use…

A: