and a 500-KVA, 1-phase transt ers are connected to the s ame bus-bars on the primary side. The secondary e.m.fs at no-load are 500 and 510 V respectively. The impedance voltage of the first transformer is 3.4% and of the second 5%. What cross-current will pass between them when the secondaries are connected together in parallel? Assuming that the ratio of resistance to reactance is the same in each, what currents will flow in the windings of the two transformers when supplying a total load of 1200 kVA. lal 290 A (b) 1577 and 900 A1

and a 500-KVA, 1-phase transt ers are connected to the s ame bus-bars on the primary side. The secondary e.m.fs at no-load are 500 and 510 V respectively. The impedance voltage of the first transformer is 3.4% and of the second 5%. What cross-current will pass between them when the secondaries are connected together in parallel? Assuming that the ratio of resistance to reactance is the same in each, what currents will flow in the windings of the two transformers when supplying a total load of 1200 kVA. lal 290 A (b) 1577 and 900 A1

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

3.8. Three identical 9-MVA, 7.2-kV/4.16-kV, single-phase transformers are con- nected in wye on the high-voltage side and delta on the low voltage side. The equivalent series impedance of each transformer referred to the high-voltage side is 0.12 + j0.82 S per phase. The transformer supplies a balanced three- phase load of 18 MVA, 0.8 power factor lagging at 4.16 kV. Determine the line-to-line voltage at the high-voltage terminals of the transformer.
6. A 5,000-kVA, 3-phase transformer, 6.6/33-kV, A/Y, has a no-load loss of 15 kW and a full-load loss of 50 kW. The impedance drop at full-load is 7%. Calculate the primary voltage when a load of 3,200 kW at 0.8 p.f. is delivered at 33 kV.
Ql-phase step down transformer 1250 KVA, 10002200 V, 50 Hz The resistance /phase and leakage reactanceiphase of the primary winding are 0.78 2 and 4.82 and the corresponding values for the secondary winding are 0.012 and 0.002 respectively if the primary winding is connected in delta and secondary in star calculate: )The voltage to be applied at normal frequency to the primary to circulate full-load through it when the secondary is short-circuited li) The full load copper loss
2. Given three identical ideal single-phase transformers with each rated at 100KVA and 7kV/3.5kV, they are connected as a three-phase transformer bank. The three-phase transformer has high voltage side connected in delta and the low voltage side is connected in wye. A three-phase 200KVA, wye connected load is connected at the low voltage side of the transformer. Calculate the following: a. Rated line-to-line voltage on each side b. Line current on each side of the transformer
A 3-phase transformer, ratio 6.6kV/33, wye/delta, 2 MVA has a primary resistance of 0.08 ohms/phase and a secondary resistance of 8 ohms per phase. The percent impedance is 7%. Calculate a. the secondary voltage with rated primary voltage and also the regulation for full load, 0.75 pf lagging conditions. b. the primary voltage with rated secondary voltage
3.8. Three identical 9-MVA, 7.2-kV/4.16-kV, single-phase transformers are con- nected in wye on the high-voltage side and delta on the low voltage side. The equivalent series impedance of each transformer referred to the high-voltage side is 0.12 + j0.82 S per phase. The transformer supplies a balanced three- phase load of 18 MVA, 0.8 power factor lagging at 4.16 kV. Determine the line-to-line voltage at the high-voltage terminals of the transformer.
The Y/Y connected 3-phase step-up transformer has a rating of 1200 MVA, operating at 33 kV/340 kV and 60 Hz. Its impedance is characterized solely by a reactance of 11.5 percent. Its purpose is to increase the voltage from a generating station in order to supply power to a 340 kV transmission line. Answer the following questions: a) Draw and determine the equivalent circuit of this transformer, per phase, in per-unit. b) Using the per-unit method, determine the generator terminal voltage when the high-voltage (HV) side of the transformer supplies 800 MVA at a power factor of 0.90 with a lagging angle, and the voltage is 360 kV. Hint: Select the nominal voltage as a base voltage, and the nominal power rating as a base power.
The equivalent resistance and reactance referred to the secondary side of a 10 kVA, 2200/440 V, single phase transformer are 0.3 and 1.20 respectively. Then find the full load voltage regulation at (i) 0.8 lagging (ii) unity and (iii) 0.6 leading power factor.
It is bartleybe's policy that if questions objective than you need to solve at least first 3 questions.
A short transmission line connects a step-up transformer on the source side with a series impedance of j0.5 ohms (referred to the primary) to a step-down transformer on the load side with a series impedance of 50 ohms (referred to the primary). The turn ratio of the step-up transformer is 1:10 and a no-load primary voltage of 23 (line-to-line) kV. The step-down transformer has a turn ratio of 35:2 and it has a Y-connected, balanced load of 0.490 +j 0.0816 ohms connected to its secondary side. A capacitor bank of -j0.171 ohms is added parallel to the load. Assuming an ideal transmission line, the load voltage (line-to-neutral) would be: O A. 7360 V O B. 6.2 kV O C. 12750 V O D. 4806 V O E. None of the other choices are correct
what is the definition of zero sequence impedance in a transformers? And what is the benefit of this check in transformers?