Analysis and design of continuous beams: Q1/ Draw the load pattern for the beams B1&B2, If imposed dead load equal to (2.5 kN/m2), and live load equal to (4.8 kN/m2),are applied on the floor ,Assume all beams have the same dimensions and the beams supports as a simply span? Y. = 24 kN / m ,all columns are (400*400)mm the secondary beam in the middle of span B2? 8m 180mm B1 5m 300mm 200mm B2

Analysis and design of continuous beams: Q1/ Draw the load pattern for the beams B1&B2, If imposed dead load equal to (2.5 kN/m2), and live load equal to (4.8 kN/m2),are applied on the floor ,Assume all beams have the same dimensions and the beams supports as a simply span? Y. = 24 kN / m ,all columns are (400*400)mm the secondary beam in the middle of span B2? 8m 180mm B1 5m 300mm 200mm B2

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the reactions of A & B for the steel bon and leasing as given abuming that 4.5 mm clearance exist bin the bar and the ground before the loads are applied. Assume E = 200 GPG. P₁ = 300 KN P₂ = 600 KN A₁ = 250 mm² A₂ = 400 mm² 5 R 4 3 2 1 & P VA 0 B P₂ 150mm 150m 150mm 150mm 4.Sm
Date: Practice Problem 1 Given the following girder properties: bne lalxA ben Properties A = 11500 mm2 y = 266x106mm* ly = 45x106mm* d. = 350 mm %3D bf = 250 mm F, = 248 MPa Fb = 148 MPa F, = 99 MPa tf = 16 mm tw =10 mm a) Find the Web Shear Capacity b) How much is the horizontal shear capacity (kN) at the neutral axis? c) If the girder was used as an 8-meter-long simple span carries equal concentration dead load, P at every quarter points and a uniform load of 12.2 kN/m, determine the load P based on shear capacity. d) Find the maximum shear stress if it is used as a 8 m beam simply supported at the left end and 2 m from the right end which carries a total uniform load of 45 kN/m.
Asap plz
Determine the maximum monent 04 the beam could cary of 3ismm fc' = 28mPa fc": fy = 375 m pa 45omm 8-28mmø Minimum concrete cover =4rmm 28mm
Determine the tributary area of purlin P1, girders G1 and G2, interior column C1, and corner column C2.
Round off the final answer to three decimal places.
M V Д A 5 K X 10'-0" 4" 4" Y Y 12" 12 K Ix = 1024 in 4 ly = 640 in 4 10'-0" 1. The 'Inverted-T' cross section below is used in the orientation shown as a cantilevered beam with two concentrated loads as indicated on the given Loading diagram. to B 4'-0" 12 K Parta Name 5 K a. Calculate the self-weight of this beam in #/ft, assuming a material density of 160 #/ft³ For Parts b-d, ignore the self-weight calculated in Part a b. What is the maximum SHEAR STRESS in the beam? Answer: c. What is the maximum FLEXURAL STRESS in the beam? Answer: 'ch sheet of significant c vided, com ernal refer 1 'm 'owable llowing hir iar d. Locate the Inflection Point along the span of the beam, calculating a specific distance from the Support at B. Indicate the location of this point on the Loading or Moment diagram.
Flexural Members:Flanged Beams 2
Determine bar force members EB, EC, and DC using method of sections. Complete solution
Assignment 1 Answer the following questions. Submit the hardcopy of your assignment before 1600hours of the 02nd June 2021. 1. A fixed beam of span 6m carries a u.d.l of 10KN/m throughout the span. It also carries a central point load of 20kN. Calculate the fixed end moments & draw SFD & BMD. Locate the point of contra flexure. 20KN -10KN/m MBA Зт 3m 2. A parabolic arch with supports at the same level is subjected to the combined loading shown in Figure 6.4a. Determine the support reactions Ay and By, horizontal reactions Ax and Bx as well as the normal thrust and radial shear at a point just to the left of the 150 kN concentrated load. 4 kN/m 150 kN 4 kN/m 150 kN 12 m A B B By 8 m 12 m 20 m Ay By (a) (b)
Find the forces acting in all members of the truss shown in Figure.(Use method of section)*
How.Draw S.F. & B.M. Diagrams For the F0 1owing Beam. 4 KN 2 KN 10 KN 3m Im