An unknown substance was subjected to boiling point determination. Temperature is recorded at 75℃ when the bubbles rigorously escapes the capillary tube and bubbles ceases at 78℃. Find the boiling point of the substance.

An unknown substance was subjected to boiling point determination. Temperature is recorded at 75℃ when the bubbles rigorously escapes the capillary tube and bubbles ceases at 78℃. Find the boiling point of the substance.

EBK A SMALL SCALE APPROACH TO ORGANIC L

4th Edition

ISBN:9781305446021

Author:Lampman

Publisher:Lampman

Chapter87: Steam Distillation

Section: Chapter Questions

Problem 2P

See similar textbooks

Similar questions

Examine the nanoscale diagrams and the phase diagram for Question 112. Match each particulate diagram (1 through 7) to its corresponding point (A through H) on the phase diagram.
Due to the fact that the liquid you used was a volatile one, it will not completely recondense. Some of the liquid remains in the vapor phase, even at room temperature. If you were able to correct for this by making the vapors recondense completely, would your final molar mass value be greater than, less than or the same as the value you determined? Explain your reasoning.
1. An organic student did an experiment extracting benzoic acid from a mixture of other organic substances. Other analyses of the obtained sample confirmed the presence of benzoic acid. The student also measured the melting point of the white solid, 117.4-121.6 oC. The literature mp of benzoic acid is 122.3oC. What can you conclude about the sample? Select one. Group of answer choices The sample of benzoic acid contains soluble impurities. The student obtained a good yield of benzoic acid. The sample of benzoic acid contains insoluble impurities. The student obtained pure benzoic acid from the extraction. The student obtained a poor yield of benzoic acid. 2. Which phenomenon are sometimes confused with melting during mp analysis? Select all that apply. Group of answer choices decomposition cracking shaking sagging/shrinking sweating solidifying 3. Study the bond types in the compound shown. Select the type(s) of intramolecular force(s) you predict the substance to exhibit. Select all…
Fully describe the steps for filling a capillary tube with a powdery solid.
When recrystalizing an aspirin sample the hot solution cooled to room temperature and no crystals appeared, so the flask was placed in Ice water. A large amount of solid appeared however the product was contaminated with impurities. explain.
X Incorrect; Try Again; 5 attempts remaining You filled in 7 of 8 blanks incorrectly. Reconsider the name for point A. You may want to review Hint 2. Define the specific characteristics of the phase diagram. Part B The phase diagram for an organic compound is shown. 1.00 - Pressure (atm) 0.50 0.10 -200 -100 100 200 Temperature (°C) What is the normal boiling point of this compound? Express your answer as an integer and include the appropriate units. > View Available Hint(s) HẢ normal boiling point = Value. Units P Pearson Ch. 2 - Chemistr..pdf Ch. 2 Note Outlin..pdf MacBook Air DII DD D00 F8 F9 F7 E5 F6 F3 F4 & #3 2$ 6 8 3
This graph shows how the vapor pressure of three liquids varies with temperature: 900 800 700 600 500 400 300 - cyclohexanone benzaldehyde dimethyl sulfoxide 200 100 150 160 170 180 190 temperature, °C Use the graph to answer the following questions: Which liquid is the most volatile? most volatile: choose one Which is the least volatile? least volatile: choose one cyclohexanone: What is the normal boiling point of each liquid? Note: your answer must be within 1°C of the exact answer to be graded correct. benzaldehyde: dimethyl sulfoxide: | °C Suppose a beaker of benzaldehyde is put inside a sealed tank containing benzaldehyde gas at 169. degree C and 704. torr. After ten minutes, will there be more liquid in the beaker, less liquid, or the same amount? more less the same vapor pressure, torr
Illustrate the phase diagram of acetone and explain your findings.
A liquid was found to be insoluble in water and soluble in cyclohexane and alcohol; the unknown was found to have a boiling point of 58°C at 670 mmHg. What is the substance? what could you do to comfirm your answer
Ice floats because of the electronegativity of oxygen that withdraws electron density from the covalently bonded hydrogens. This results in a permanent dipole, leaving a partial positive charge on the hydrogens. The extra electron density on the oxygen leaves a partial negative charge. Therefore, water is a polar molecule and has the ability to form hydrogen bonds. These properties explain many of water's characteristics, including why ice is less dense than liquid water. Sort the following images into phases of water. 1. Drag and drop options on the right-hand side and submit. For keyboard navigation... SHOW MORE ✓ Image 1 Image 2 2. Image 3 = ||| 3. State of water that is most dense Molecules with lowest kinetic energy Phase of water present at highest temperature K 7 Open
Explain the permanent dipoles ?
Chemistry 5. You melt the substance and de-coloration occurs. Unfortunately, you weren’t paying attention and miss the melting point. Should you start over or re-melt it? Or both are options ‘okay’? 6. When measuring the melting point of a substance, it suddenly disappears. What has happened? Can you still measure the melting point? If so, how? 7. We should not re-use a sample in a capillary tube for melting point measurement. Why not? 8. It takes significant amount of time for the melting point apparatus to cool down before next measurement if your new sample has a lower melting point than your previous one. What can you do to reduce this time in between measurements when many samples of different melting points are used?