An unfinned single-pass cross-flow heat exchanger is being designed with an available surface area of 0.471 m². The hot fluid (specific heat of 3120 J/kg-K) flows through the tubes with a mass flow rate of 0.4 kg/s. The cold fluid (specific heat of 4100 J/kg-K) has a mass flow rate of 0.2 kg/s. The overall heat transfer coefficient of the heat exchanger is 1100 W/m².K. Find the effectiveness of the heat exchanger. Assume thin copper tubes are used and neglect radiation. 0:404

An unfinned single-pass cross-flow heat exchanger is being designed with an available surface area of 0.471 m². The hot fluid (specific heat of 3120 J/kg-K) flows through the tubes with a mass flow rate of 0.4 kg/s. The cold fluid (specific heat of 4100 J/kg-K) has a mass flow rate of 0.2 kg/s. The overall heat transfer coefficient of the heat exchanger is 1100 W/m².K. Find the effectiveness of the heat exchanger. Assume thin copper tubes are used and neglect radiation. 0:404

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Heat Exc
A counterflow, concentric tube heat exchanger is designed to heat water from 23 to 80 deg C using hot oil,which is supplied to the annulus at 163 deg C and discharged at 140 deg C. The thin-walled inner tube has a diameter of Di=23 mm and the overall heat transfer coefficient is 500 W/m2. K. The design condition calls for a total heat transfer rate of 3300 W. What is the length of the heat exchanger? Select one: a. 0.49417 b. 1.1269 c. 0.92237 d. 0.6234
A 1-2 shell and tube heat exchanger is used to heat water from 60 to 90°C. Oil (Cp=2.3 kJ/kg-K) is used as the heating fluid and flows in the shell side at 150°C. The mass flow rate of the water is 5000 kg/hr while that of the oil is 10,000 kg/hr. The tubes are 1½ BWG 10 copper pipes (k = 385 W/m-K). The shell side heat transfer coefficient is 2500 W/m²-K while the tube side heat transfer coefficient is 1000 W/m²-K. Calculate: a. the exit temperature of the oil b. the total length of tubes required
Flowing juice like 0.5kg / h enters the parallel-flow heat exchanger at 293 K and is heated by 400K water vapor (Cp = 1.76kJ / kgK), which is 2.5 kg / s. The exit temperature of the juice is 360 K, the area where heat transfer takes place Calculate the efficiency and heat transfer of the heat exchanger if it is 20 m2 and the overall heat transfer coefficient is 280W / m2K. (physical properties of fruit juice will be considered the same as water).
A 2 - shell pass & 4 - tube pass heat exchanger is designed to heat water from 40 C to 90 C flowing inside the tubes at a rate of 7.5 kg/sec while hot gases flowing in the shell at a rate of 10.42 kg/sec with temperature leaving the heat exchanger at 110 C. Consider the specific heat of water and gas of 4.2 kJ/kg K & 1.08 kJ/kg K, respectively. Draw the temp-profile showing the multi-pass effect and determine the temperature of gas entering the heat exchanger.
310 m algunaourtsdi bayon bozu (A) In a food processing plant a brine solution is heated from 6°C to 12°C in a double pipe heat exchanger by water entering at 50°C and leaving at 40°C at the rate of 0.166kg/s. If the overall heat transfer coefficient is 850 W/(m².K), what heat exchanger area is required for (1) parallel flow heat exchanger and (2) counter flow heat exchanger. Discuss the results?. Take C₂ (for water)= 4.180 kJ/kg.K mbmeod (isolev si ma do liw novel
In practical applications of heat transfer enhancement techniques, what performance objectives are considered for optimizing the use of heat exchangers?
Calculate the liquid flow rate for a heat exchanger with one tube pass. The liquid is heated from 20°C to 93°C by a hot gas at 260°C and 0.45 kg/s. A-4.64 m², U-280 W/m²
Write down the total thermal resistance for a double-pipe heat exchanger. Show how to convert from total resistance to an overall heat-transfer coefficient. Explain how flow regime may affect overall heat transfer rate.
Glycerin (cp=2400J/kgK) at 20oC and 0.5kg/s is heated by ethylene glycol (cp=2500J/kgK at 50oC at the same mass flow rate. The overall heat transfer coefficient for this thin-walled double-pipe parallel flow heat exchanger is 380W/m2K and the heat transfer surface area is 6.5m2. Determine Cmin and Cmax Find c, e, and NTU Determine heat transfer rate for the heat exchanger. Determine the outlet temperatures of both fluids.