An rectangular orifice with height 0.4 m and width of 0.6 m was used to measure the flow of a certain channel. Flow was controlled such that the  entirety of the discharge will be focused and exit on the orifice. Upon stabilization of conditions, it was observed that the height of the water above the  orifice can be taken as 1.2 meters and for a certain section upstream before the orifice, velocity can be considered constant at 1.7 meters per sec- ond. Assume your own water temperature and compute for the stream discharge considering a discharge velocity of 0.6812.

Q: = 3.7.9. The water surface elevation difference between two reservoirs 2,000 m apart is 26 m.…

A:

Q: The flow in a cylindrical pipe that has a diameter of 0.9 m is 3 m³/min. What is the velocity of the…

A: Diameter of pipe (d) = 0.9m Flow rate (Q) = 3 m3/min Determine the velocity of the water in m/s.

Q: In March of 1996 a special release of water, U Canyon Dam, to create an artificial flood in the…

A:

Q: Q- In a laboratory, a flow experiment is performed over a hydraulic structure. The measured values…

A:

Q: The actual velocity in the contracted section of a jet of liquid flowing from a 50mm diameter…

A:

Q: Show step by step solu

A: Q=1.555D2Explanation:

Q: EXAMPLE: For the shown system below, the following is given: L = 300 m e = 0.2 mm v(Nu)= 1 x 10-6 m2…

A: Given, L= 300 m D= 100 mm e=0.2 mm H= 60 m ν=1×10-6 m2/sec Turbulent flow

Q: The peak flow of an inflow hydrograph to a reservoir is Qp. It begins to flow into a large reservoir…

A:

Q: 1) You have used a Manning n value of 0.009 for the open channel in the lab. You would expect…

A: "Since you have posted a question with multiple sub-parts, we will solve first three sub parts for…

Q: Q-1: The performance of a spillway of a power project is to be studied by means of a model…

A:

Q: An inflow hydrograph to a 20 m wide x 85 m long x4 m (max height) detention basin has a constant…

A:

Q: A channel with a cross section shown in the figure below has a flow of 10.5 m's. The slope of the…

A: Solution (a) Channel bottom slope, S = 10105 = 10-4 roughness, C =40 Q = 10.5 m3/s Assume depth of…

Q: Q-1: The performance of a spillway of a power project is to be studied by means of a model…

A:

Q: 7. A stream having a discharge of 280L/sec per meter width of channel has a depth after the jump of…

A: Let V1 be the velocity of water before jump. y1 be the depth before jump. - Find Depth before jump…

Q: a discharge of 700L/s flows through a pipe having a diameter of 400mm and a length of 60m long.…

A:

Q: A hydraulic jump is situated a 4 m wide rectangular channel. The discharge in the channel is 7.5…

A:

Q: In an experiment on a trapezoidal notch the flow is collected in a 3.37 meter diameter vertical…

A:

Q: Two small circular orifices of diameters d, and d,, respectively, are placed on the side of a tank…

A:

Q: Example 8: A flocculation basin is designed to treat water of 1 m³/s flow rate. The length of the…

A:

Q: In a wide rectangular channel with uniform flow the specific energy is 1.08 m. What is the velocity…

A:

Q: In a laminar flow through a circular pipeline of 20 cm diameter, the flow velocity at a hadial…

A:

Hydrogen Energy

Energy is a quantity that cannot be defined, its existence can only be felt. In simple language, if a system possesses energy, it can do a specific kind of work. There are many forms of energy sources which people can use to obtain work. Solar energy, tidal energy, hydroelectric energy, geothermal energy, wind energy are some of the renewable energy sources which are primarily used for the production of electricity.