An R-22 compressor has a 5 percent clearance volume and a displacement rate of 80 L/s and pumps against a condensing temperature of 40°C. For the two different evaporating temperatures of -10 °C, compute the clearance volumetric efficiency.

An R-22 compressor has a 5 percent clearance volume and a displacement rate of 80 L/s and pumps against a condensing temperature of 40°C. For the two different evaporating temperatures of -10 °C, compute the clearance volumetric efficiency.

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter40: Typical Operating Conditions

Section: Chapter Questions

Problem 9RQ: The evaporator design temperature may in some cases operate at a slightly ____(higher or lower)...

See similar textbooks

Similar questions

Please calculate enthalpies and the heat of a condenser and evaporator. Thank you
Question 2: Consider a 3 effects evaporators supplied with live steam (135°c) at 130°c. Inlet sea water temperature to the first effect is 30°c. If the temperatures in the 2nd and 3rd effects are 100°c and 70°c respectively, calculate the amount of distillate per kg of: 1) Supplied steam 2) Inlet sea water Assume, perfect heat transfer, (m./m,= 0.5= Recovery ratio) and vapor gives up latent heat only in each effect (neglect blow). Salinity of outlet brine has a maximum value as twice as that of inlet sea water
I need the answer as soon as possible
Kindly solve fast
b) The high pressure units on a steam plant operate at 10bar (gauge), and the condensate is sub-cooled by 9.5K. If the mass flow rate of condensate is 10 kg/s, use the provided steam tables to determine how much saturated steam at 1.5 bar this condensate could produce. Note it is sufficiently accurate for high pressure condensate, as in this question, to assume that the specific enthalpy is the same as for the saturated liquid at the same temperature.
Liquid ammonia at a temperature of 26°C is available at the expansion valve. The temperature of the vaporizing ammonia in the evaporator is 2°C. Find the percentage of liquid vaporized while following throgh the expansion valve. Abs. Pressure kPA Enthalpy kJ/kg hfe 190.4 1255.2 1445.6 303.6 1162.0 Temperature "C 2. 26 462.49 1033.97 1465 6
6- The following reading were taken during a test on a surface condenser: Mean condenser temperature = 35°C Hot well temperature = 30°C Condenser vacuum = 69 cm Hg Barometer reading = 76cmHg Condensation rate = 16 kg/min Cooling water temperature inter = 20 °C Cooling water temperature outlet = 32.5 °C Flow rate being = 37500 kg/h Calculate: a- mass of air present per cubic meter of condenser b- quality of steam at condenser inlet c- vacuum efficiency d- condenser efficiency (condenser heat transfer effeteness)
3.) An ammonia compressor operates at evaporator pressure of 316.02 kPa and a condenser pressure of 1557 kPa. A twin-cylinder compressor with bore to stroke ratio of 0.85 is to used at 1200 rpm. The actual volumetric efficiency is 92% and compression and mechanical efficiency is 78% and 80% respectively. For a cooling capacity of 25 TR, (a) the sketch the p-h diagram labeling the evaporating and condensing temperature and pressures (b) define the all properties of ammonia taken from saturation table. Determine (c) the quantity of cooling water in the condenser in kg/min if the increase in temperature is 8°C, (d) the bore and stroke expressed in cm and (e) the size of the driving motor in hp. Given: h2 = h at 1557 kPa and s2 = s1 1695 kJ/kg
Please add units.
Q.1. A refrigeration process with interstage cooling uses refrigerant HFC-134a, and the outlet of the condenser is to be saturated liquid at 40°C. Refer to the following figure for stream numbers in your solution. The pressure of the flash chamber and the intermediate pressure between compressors is to be 290 kPa. The evaporator is to operate at -20°C and the outlet is to be saturated vapor. The flowrate of stream 1 is 23 kg/h. The flash chamber may be considered adiabatic. The compressors may be considered to be 80% efficient. a) What is the power input required to the first compressor? b) What are the flowrates of streams 6 and 7? What is the enthalpy of stream 4? Hot Side 6 5 Condenser 2nd Stage Compressor Throttle Valve 7 Flash Chamber Vapor Phase Only 1st Stage Compressor 8 Throttle Valve Evaporator 1 2 Cold Side
Example (2): a 5400 kg/hr of steam is supplied by a certain boiler plant at pressure (750 kPa) and dryness fraction 0.98. Feed water is supplied at a temp. (41.5°C). The mass of fuel (coal) is (670 kg/hr) with L.C.V = 31000 kJ/kg. Determine: a) The boiler efficiency. b) The equivalent evaporation E.E. at 100°C. c) The saving in coal per hour if the economizer is fitted in the flue gases (the feed water temp. can be raised to 100°C), assuming the other conditions are the same.
I have step by step but I don’t know how to read table and values ! Help with final calculations