An overall noise temperature of 70 K is required for a three-stage amplifier. The amplifier must have at least 45 dB of total gain. The amplifier will be constructed by adding a low-noise first stage to an existing amplifier with the following characteristics: Stage 2 has a 20-dB power gain and a 3-dB noise figure. The third stage features a 15-dB power gain and a 6-dB noise figure. Determine the first stage's maximum noise figure. Select your answer. 0.565 dBm 1.139 dB 60.565 dBµ 30.565 dB

An overall noise temperature of 70 K is required for a three-stage amplifier. The amplifier must have at least 45 dB of total gain. The amplifier will be constructed by adding a low-noise first stage to an existing amplifier with the following characteristics: Stage 2 has a 20-dB power gain and a 3-dB noise figure. The third stage features a 15-dB power gain and a 6-dB noise figure. Determine the first stage's maximum noise figure. Select your answer. 0.565 dBm 1.139 dB 60.565 dBµ 30.565 dB

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

For an operational amplifier, the differential gain and the common mode gain is 5555 and 5 respectively. What will be the CMRR of the opamp? Can be opamp be called a good opamp based on CMRR?
Please provide solution in 30 minutes
Determine the noise figure in decibels and equivalent noise temperature for the non- ideal amplifier that has the following parameters. Assume that the ambient temperature is 290 Kelvin. (b) Input signal power = 2.0x10-10 W Input noise power = 3.5x10-17 W Power gain of the amplifier = 10 Internal noise power (generated in the amplifier) = 5.5x10-12 W A specified gain of 9 dB and a noise figure of 4.5 dB are specified for an amplifier. What is the equivalent noise temperature in Celsius? Then, if three identical amplifiers are cascaded together, determine the overall effective noise figure and noise temperature. Assume that the ambient temperature is 290 Kelvin. (c)
4-The pinchoff voltage has the same magnitude as the a-Gate voltage b-Drain-source voltage c-Gate- source voltage d-Gate-source cutoff voltage 5-The transconductance curve is a-Linear b-Similar to the graph of a resistance c-Nonlinear d-Like a single drain curve 6-A cascade amplifier has the advantage of a-Large voltage gain b-Low input impedance c-Low input capacitance d-Higher gm 7-To get a negative gate-source voltage in a self-biased JFET circuit, you must have a a-Voltage divider b-Source resistance c-Ground d-Negative gate supply voltage 8-When a JFET is cut off, the depletion layers are a-Touching b-Conducting c-Close together d-Far apart.
11- In the figure shown below a noninverting amplifier have Vi = 2 V, Rr = 500 k2, and R1 = 100 k2. The output voltage will be i. 9V ii. 10v Opang ii. 1IV iv. 12V
(b) Design a non-inverting amplifier to provide a closed loop gain of 60. Draw the schematic and briefly explain its operation. (c) You have built the circuit from the previous question (A1 (b)) and are testing its output for an AC input signal with 10 mV peak amplitude. The output signal measured on the oscilloscope has peak amplitude of approximately 420 mV. Assuming your measurements are correct, is this what you expected? Provide a possible justification for this result.
Sid nov
The noise figure of an amplifier is 56 dB. Calculate the output signal-to-noise ratio when the input signal-to-noise ratio is 70 dB.
Problem 1 - Design an inverting amplifier with a gain of -24. Please draw the resulting circuit and block diagram.
Which of the following is not a terminal for the operational amplifier? a) Inverting terminal b) Non-inverting terminal c) Output terminal d) None of the mentioned
Consider the two-stage amplifier in the figure below. The first stage is a differential amplifier and the second stage is a difference amplifier. Assume that Rg = 20k and you may ignore any early voltage effect. Further assume that Rc = 10k, R3 = 300k and R4 = 100k. What would be the estimated differential gain of the first stage amplifier? CRB close to 200 RB Q4 V01 Stage 1 Q3 O a. O b. close to 150 O c. close to 600 O d. close to 500 e. More information is required to calculate the gain Cm RC Q2 V02 RA R4 R3 Stage 2 -R3 741 + +10v į -10V
Note: Answer all questions Questions' marks B The parameters for the summing amplifier in Figure below are: Rp 100 kl, and R3 The inpul voltages are ,=4+125sinwt mV and V=-6 mV. Determine R, and Rz to produce an output voltage of vo -0.5sinot V. i4 RI looKe ww Is. RF R1 V =0 i2 R2 Iu.あ R3 Ra 8.