An open rectangular tank measuring 5 m long, 1.99 m wide, and 2 m high is filled to a depth of 1.6 m with water. The tank is attached to a truck that is traveling horizontally at 9.81. How much water (m3) is left if the track is traveling horizontally at 9.81 m

Q: 10. The first digital code was the: a. ASCII code b. Baudot code c. Morse code d. none of the above

A:

Q: Q1. Figure shows a cross section view of a structure. All dimensions are in mm. (a). Determine the…

A: Solution: Given:

Q: Determine the x- and y-coordinates of the centroid of the shaded area. Y 50 1 1 150 50 Answers:…

A: To find out the X and Y coordinates of the centroid of the shaded area.

Q: Add/Subtract the following DMS measurements by hand. In your answer, separate each unit by a comma…

A:

Q: When are the singularity functions used?

A: Solution-  We can observe that the shear and bending moment expressions get increasingly complicated…

Q: To draw the figure below, the most :important command is Array O Trim O Сopy O Offset

A: Given data Grid of shape To be discussed Which command to be used

Q: In the MIPS instruction "jr $1", what information does register $1 contain?     the address of the…

A:

Q: Note: Replace all zero digits of your ID number by number "2" Problem #4: A 8 = 10+C (degrees) В C…

A:

Q: Calculate the y-coordinate of the centroid of the shaded area. The triangle is equilateral.…

A:

Q: The timber beam in Figure 2 is simply supported at points A and E. The cross-section of the beam…

A: E = 12 GPa Use virtual method to analyze the beam.

Q: Break the shaded area into the five different areas shown. Find the area and the x- and…

A: Determine  a. Break the shades area into the five different area and find area, x and y coordinates…

Q: A clockwise couple M = 4.5 N m is resisted by the shaft of the electric motor. (Figure 1) Part A…

A: Given: The moment M is 4.5 N.m. Consider the figure,

Q: Note: Replace all zero digits of your ID number by number "2" Problem #4: Use X = Last 3 digits of…

A:

Q: Determine the coordinates of the centroid 120 mm 240 mm uu ost

A: In a body, the centroid is the point where all its sides have the same volume. Those made from one…

Q: A line was measured as 79.52 Chains. What is the length of the line in feet? (to nearest 0.1 foot)

A: 1 chain = 66 feet 79.52 chains = 79.52 x 66                         = 5248.3 feet

Q: Convert 1600 mils into equivalent value in grads O 90 degrees O 180 degrees O 270 degrees

A: To convert mils to degree

Q: Line P to Q intersects the street alignment as shown in the sketch below. What is the length of line…

A:

Q: uO 9:1 * Asiacell lin. yols- i docs.google.com 14. Which is NOT a unit of length measurement? Yards…

A: 1.Hear in this question Grads are not units of linear measurements or length measurements, since…

Q: determine the centroid of the area shown with respect to the given x-axis

A:

Q: Break the shaded area into the five different areas shown. Find the area and the x- and…

A:

Q: You are a professor of architecture. Show your students where the horizon line and vanishing points…

A:

Q: Find the centroidal distances from x axis and y axis

A: Consider the figure,

Q: Determine the coordinates of the centroid of the shaded area. y 15 E 30 35 15 40 50 30 --X 100…

A:

Q: Use the method of compsite areas to calculate the centroidal coordinates of the plane regions shown…

A:

Q: The section comprising of two 250 x 37 channels shown was built-up in such a way that their…

A:

Q: Z 10 mm 15 15 430 y y -y y 15 100 All dimension in mm FIGURE Q3 (a) FIGURE Q3 (b) IN

A: The dimensions of channel section are given.two channel sections are arranged back to back with 10mm…

Q: What of the following about the scale is/are false ?

A: The scale represents the ratio between the measurement drawn in a plan to the actual measurements.

Q: y. 50 -30- 40 15 Dimensions in mm to

A:

Q: For the cross-section shown below, the centroid value from the top surface in inches is: * 0.5 in.-3…

A:

Q: How does GPS works?

A: GPS has three components which are- 1) Satellites - These are responsible for send and receive…

Q: Determine the centroidal coordinates (x, y,z) of the volume.

A: Question is based on the section . Dimension of section are given in the question . Centroidal…

Q: Hand Writing not allowed please provide Typed answer

A: The distance between v1 and v2 is  √37 or approximately 6.08 units.Explanation:Formula for distance…

Q: Calculate the y-coordinate of the centroid of the shaded area. The triangle is equilateral. 16 35 +…

A:

Q: Draw the flowchart to calculate the area of ​​the two shapes and print the smallest of them

A: Using rectangular area calculation (a X b) Rectangular area is calculated, similarly using isosceles…

Q: express each measurement in feet.108 inches

A:

Q: For the non-standard shape show etermine the location of centroid moment of inertia and radius of…

A:

Q: Please recheck and answer in 3 decimal places.

A:

Q: Two springs are used to support the steel truss structure of 2.5 m height shown in the figure. The…

A: Given: Spring 1: (right support) Shear modulus, G1=300+41=341 GPa Spring diameter, d1=20 mm Helical…

Q: create a graph showing the value of the air density as a function of temperature. The Command Window…

A: The density of dry air can be  expressed as a function of temperature and pressure.…

Q: Locate the centroid of the given area below. Semi-Circle Square

A:

Q: Choose the answer that shows 21' 11-1/4" converted to decimal feet. O 21.95 feet O 21. 9 feet O…

A: answer = 21.94 feet

Q: Determine the coordinates of the centroid of the shaded area. 10 40 y X = K15 Answers: y= i 10 |10|…

A:

Q: 4. Complete the accompanying set of profile notes and perform the arithmetic check. Provide a sketch…

A: The levelling terms and formula. BS = Back sight The first measurement taken in a survey. It is the…

Q: B. Describe the major elements that geometric design of highways deals with? (write between 100-150…

A: Geometric design of highway: A highway has many visible dimensions both in the horizontal and…

Area Computations

The area is the mathematical estimation of the inner space occupied by any shape or object and area computation is the evaluation of how much inner space that particular shape or object has utilized. Simple applications include calculating the area of wall for the quantity of paint or plaster to be applied on it, area calculations for construction of a trapezoidal dam and how much material is required, calculating the area of a circle to determine the range or distance of wheels that they are capable of covering due to varied radii and so on.