An open cylindrical tank 2m in diameter and 4m high contains water to a depth of 3m. It is rotated about its own vertical axis with a constant angular speed w. If w = 4 radsec, what is the volume of liquid spilled?

Q: A = 1.94.hmax = 0.559.R = 206 1. Filling the tank (30%) a) If the tap on the output pipe is closed…

A: A = 1.94hmax = 0.559R = 206FINDa) If the tap on the output pipe is closed (i.e. R = ∞) determine how…

Q: D A cylindrical tank with its axis vertical gas a diameter of 2 m and a depth of 8 m. A standard…

A:

Q: From the figure below, the tank contains 2 layers of liquid. H of water = 2 m, H of SG = 1 m.…

A: To Determine Specific gravity of the liquid.

Q: A rectangular tank 3 m long, 1.40 m wide and 1.80 meter high contains oil with specific gravity of…

A:

Q: An open vessel in the form of a frustum of a cone with a radius of 1.2m (bigger base), the smaller…

A: The radius of frustum at base, R=1.2 m The radius of frustum at top, r=1 m The slope of vertical…

Q: Alm-diameter pipe bend shown in the diagram is carrying crude oil (S=0.94) with a steady flow rate…

A:

Q: A 50 mm diameter siphon draws oil (S.G. = 0.82) from a reservoir. If the head loss from point 1 to…

A:

Q: An open tank has a vertical partition and on one side contains gasoline with a density p = 700 kg/m³…

A: Gate will start to open when the force from water side will be greater than gasoline side When Force…

Q: An open trapezoidal tank having a bottom width of 3 m is 2 m high, 1.5 m wide, and has its sides…

A:

Q: Calculate the discharge through the orifice.

A:

Q: A sharp-edged circular nozzle with a cross-sectional area of 10 cm2. Water flows from it under the…

A: Actual velocity calculation:…

Q: 17. An open cylindrical tank 4 m in diameter and 10 m high contains 4 m of oil sg = 0.9. An orifice…

A: The objective of the question is to calculate the time required to discharge all the oil from a…

Q: Oil (SG = 0.86) is passing through a horizontal pipe whose diameter increases from 150mm diameter at…

A:

Q: Water flows through a pipe before passing through a nozzle and exiting as a free jet to the…

A: In this question we use a) coefficient of contraction formula Cc = (Area of jet at vena contracta /…

Q: Liquid 1 SG X y Liquid 2 SG: --- ----- Both the top of the tank and the end of the slanted tube are…

A:

Q: The ball B of negligible size rolls through the tube such that at the instant shown in (Figure 1) it…

A: Given: To find: Part A: Velocity of the ball if the tube has an angular velocity, ω = 3 rads/s and…

Q: 5. A right circular tank 6 m in diameter and 12 high is filled with 6 m of oil sg = 0.88 and 6 m of…

A: Diameter of tank = 6 m Initial Height of fluid = 12 m Diameter of orifice = 75 mm

Q: Question- A pelton wheel works under a head of 400m. Friction loss through the pipe flow is limited…

A: Given- Pelton wheel- Head h=400 m, friction loss=10%, Coefficient of velocity Cv=0.98, g=10 m/s2, It…

Q: Q.13.18 MASS FLOW AT A PIPE JUNCTION Cousuier the steady flow in a water pipe joint shown in the…

A:

Q: Gasoline (SG=0.7) flows down an inclined pipe whose upper and lower sections are 90 mm (section 1)…

A:

Q: 2. An open cylindrical vessel, 800mm in diameter, 1.2 meters high, and 3/4 filled with water rotates…

A:

Q: 5. A right circular tank 6 m in diameter and 12 high is filled with 6 m of oil sg = 0.88 and 6 m of…

A: Diameter of tank = 6 m Initial Height of fluid = 12 m Diameter of orifice = 75 mm

Q: In a two dimensional incompressible, steady flow, stream lines are drawn so that they are 26 im…

A:

Q: hydraulic pump increases the pressure in a system from 500 kPa to 3 MPa at a flow rate of 2 e/s. The…

A:

Q: Situation 3: A tank with a frustum of a cone having its bases horizontal and axis vertical is 4 m…

A:

Thermal Processes

Some of the key areas where thermal processes find their application are: