An open belt running over two pulleys 24 em and 60 cm diameters connects two parallel shafts 3 m apart and transmits 3.75 KW from the smaller pulley that rotates at 300 r.p.m. coefficient of friction between the belt and the pulleys is 0.3 and the safe working tension is 100 N/em width. Determine: i) minimum width of the belt, ii) initial belt tension, and i) length of the belt required

Q: Determine the reaction forces at the four contact points A, B, C and D. Small: Mass of 1.02 kg…

A:

Q: Prob # 9. Find the horsepower transmitted by a pair of friction wheels, the diameter of driving…

A:

Q: 3. A V-belt drives a pulley at a speed of 1440 m/min. The coefficient of friction between belt and…

A: Given data: - The speed of the belt is v = 1440 m/min. The friction coefficient between belt and…

Q: 300 rpm. The coefficient of friction between the belt and the pulley is 0.26, angle c lap 160° and…

A:

Q: the block A vertical

A:

Q: Find the power transmitted by a belt running over a pulley of 500mm diameter at 300 rpm. The…

A: It is the very basic problem of machine design and the topic is design of belt .

Q: A pulley system uses a flat belt of cross sectional area 500 mm2 and density 1300 kg/m3. The angle…

A: cross-sectional area, A = 500 mm^2 density = 1300 kg/m^3 angle of lap = 165 degree coefficient of…

Q: As shown in the figure below, three boxes are placed on an incline. The boxes are initially in…

A: Given data as per the question Mass of block A =20 lb Mass of block B= 40 lb Mass of block C = 30 lb…

Q: Two identical pulleys with diameter of 711 mm, are mounted on two parallel shafts for flat belt…

A:

Q: An open belt connects two flat pulleys. The pulley diameters are 300 mm and 450 mm and the…

A:

Q: A leather belt of thickness 6 mm and width 80 mm connects two pulleys of 500 mm diameter and 900 mm…

A:

Q: B) A body is pulled by a rope which passes 3 times round a power-driven capstan 600 mm diameter,…

A:

Q: In an experiment to find the coefficient of static friction, two plates (e) made of the sam…

A: cosθ N for m1=0.2kg N for m2=0.4kg cos20 1.87 3.75 cos30 1.73 3.46 cos40 1.53 3.06

Q: The pulley of Fig. wheel that fits loosely over a t in.-diameter shaft. A rope passes over the…

A: Given: The diameter of the wheel, D = 4 in The diameter of the shaft, d = ½ in The magnitude of…

Q: Q2 ) A cone clutch is to transmit 10 KW at 600 r.p.m. the cone has a face angle of 10° The width of…

A: Given,  Power transmitted , P =10 Kw Speed, N =600 rpm Cone angle = 10 degree maximum pressure , Pr…

Q: Don't use chatgpt will upvote

A: Valuable Concepts: Relationship between Force and WorkRelated rates in dynamicsWork-Energy…

Q: ** Please label the question answers so I could understand it better! Thank you! Scenario: A chair…

A:

Q: Q: Block(A) of weight (100kN) is tied to block (B) of unknown weight (WB) through a flexible cable…

A: From the information given, Weight of block A = WA = 100 kN Coefficient of friction for block A = μA…

Q: A reciprocating compressor is driven by a standard three-phase motor with a rated speed of 1490…

A: The theoretical length of the belt.Given:The diameter of the larger pulley is .The diameter of the…

Q: Two blocks are connected by a strut of negligible weight with frictionless pins. The coefficient of…

A:

Q: Q) A single plate clutch has to transmit 75 kW at 3000 r.p.m. The spring exerts an axial pressure of…

A: The answer is

Q: The pulley of Fig. wheel that fits loosely over a t in.-diameter shaft. A rope passes over the…

A: Consider the Free body diagram of the system when θ = 90o and the weight is getting lowered with no…

Q: A 75-Kg man wants to pull a 145- Kg box and the coefficient of static friction between the box and…

A:

Q: Calculate the total power needed from the motor to drive an electrical conveyor belt, which carries…

A: The total power needed from the motor to drive an electrical conveyor is 10.8137 kW.

Q: Two parallel shafts whose centre lines are ‘5’ m apart, are connected by an open belt drive. The…

A: C=5 mD=3 md=3 mTmax=4 KNμ=0.3N=700 rpmVelocity of belt, V=π*d*N60V=π*3*70060=109.95 m/s

Q: (b) A block weighing 2000 N is on a rough inclined plane that makes angle of 15° with horizontal.…

A: Given:W=2000 Nθ=15°F=800 N

Q: Coefficients of Static Friction: Steel on Rope: 0.3 Try to pull an Acme brand safe off of a stone…

A:

Q: Jestion 3 A flat belt drive connects two pulleys 5 meters apart: The 2m pulley diameter driver…

A: Given, Distance between the two pulleys, L=5mDriver diameter, D1=2mN1=350rpmDriven diameter,…

Q: QUESTION 6 The coefficients of friction are u s = 0.30 s and uk= 0.20 between all surfaces of…

A: Handwriting.jpg

Q: A simple flat belt drive system shown in the figure has a driving pulley diameter 220mm and runs at…

A:

Q: 2. A block of mass m, = 20 kg which lies on an incline frictional surface is connected to another…

A:

Q: Two pulleys which are 270 mm in diameter and which are run at 1030 rpm are connected by a V-belt…

A:

Q: An open belt connects two flat pulleys. The pulley diameters are 300 mm and 450 mm and the…

A: Given data as per question d=300 mmD=450 mmθ=160×π180=2.79 radμ=0.35N=200 rpmp=3kw=3000…

Q: Two pulleys rotating in opposite direction has the following properties: D1 = 430 mm, D2 = 180 mm,…

A: The given information in the problem is listed in the following attached image:

Power Transmission Elements

It is defined as the energy transfer from one location to another location. The energy will start moving from the energy generation source to the energy applied position to obtain the work output. From this method, a large amount of electric energy moves from the power station to various electrical substations.