An oil tank can be filled by pipe X in 5 hours and pipe Y in 4 hours, each pump working on its own. When the oil tank is full and the drainage hole is open, the oil is drained in 20 hours. If initially the tank was empty and someone started the two pumps together but left the drainage hole open, how many hours will it take for the tank to be filled? (Assume that the rate of drainage is independent of the Head)

An oil tank can be filled by pipe X in 5 hours and pipe Y in 4 hours, each pump working on its own. When the oil tank is full and the drainage hole is open, the oil is drained in 20 hours. If initially the tank was empty and someone started the two pumps together but left the drainage hole open, how many hours will it take for the tank to be filled? (Assume that the rate of drainage is independent of the Head)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Not sure how to do this one. Would appreciate a full solution, thanks! Textbook Answer: (c) II and V
Please answer in 5 mins a tank is initially filled of capacity of 25 L with brine having a salt concentration of 5 g/L. water containing 1 g/L of salt is entering at a rate of 4 L/min, and he mixture is allowed to flow out of the tank at a higher rate of 6L/min. find the concentration (g/L) of salt when the amount of water left in the tank is half the initial amount Topic applications in DE about mixture
Non-positive displacement pump is the type of pump whose size is lesser for a given discharge räte. Select one O True O False
Moving to another question will save this res ion 39 A 128-mm-diameter pipe enlarges to a 146-mm-diameter pipe. At section 1 of the smaller pipe, the density of gas in steady flow is 263.178 kg/m3, and the velocity is 22 m/s; at section 2 of the larger pipe, the velocity is 15 m/s. Find the unit weight (in kN/m3) of the gas at section 2. Round off to three decimal places. < Question 39 of 48 A Moving to another question will save this response. F12 PAUSE కాజా F10 F11 DELETE F4 FS F6 F7 FB F9 F2 F3 BREAK F1 ESC % $ 4 NUM LK @ %23 5 6 { } Y P HOME ENTER G H J K A SHIFT V CTRL V 因

Given the following average hourly demand rates in gallons per minute, (a) findthe uniform 24-hour pumping rate and the required storage necessary to supply for this demand;(b) if the period of pumping is 12 hours (from 12 am to 12 pm) find the required storage.
PLEASE ANSWER
Dechlorination contact tank (Wastewater Treatment) An activated sludge plant has a design flow (average daily flow) of 11 MGD. Determine dimensions of dechlorination tank. The design parameters: use 1 tank. detention time = 30 sec, depth = 10 ft, rectangular tank: L = 4 W. use maximum hourly flow (3 * Average design flow)
Part 1 Part 2 Part 3 hp A centrifugal pump having a 7.5-in-diameter impeller and the characteristics shown in the figure below is to be used to pump gasoline through 4000 ft of commercial steel 3-in.-diameter pipe. The pipe connects two reservoirs having open surfaces at the same elevation. Determine the flowrate. Do you think this pump is a good choice? This figure is referred to as the pump performance characteristics. 500 8 in. dia 400 7 出300 6 Head, ft 200 100 65 60 55 50 40 bhp 30 25 20 80 ° 40 120 160 200 240 280 320 Capacity, gal/min Write the system equation for this flow system as function of the friction factor f and volume flowrate Q in gal/min. (Use 2 significant digits on coefficients. Do not enter units as a part of your response.)
PLEASE HELP ME ANSWER THIS ASAP. NOTE: COMPLETE SOLUTION WITH PROPER FIGURES. 3 DECIMAL PLACES
I need solution in half time please