An n-p-n transistor at room temperature has its emitter disconnected. A voltage of 5 V is applied between collector and base. With collector positive, a current of 0.3 μA flows. When the base is disconnected and the same voltage is applied between collector and emitter, the current is found to be 25 µA. Find and a, IE, Ip when collector current is 1 mA.

An n-p-n transistor at room temperature has its emitter disconnected. A voltage of 5 V is applied between collector and base. With collector positive, a current of 0.3 μA flows. When the base is disconnected and the same voltage is applied between collector and emitter, the current is found to be 25 µA. Find and a, IE, Ip when collector current is 1 mA.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

a) Draw the energy band diagram of a MOSFET transistor, when -5 volts are applied to the drain contact. b) Explain what will happen to the Fermi level at the source contact and the drain contact in the following scenarios (Use an appropriate energy diagram to illustrate your answer): A positive voltage is applied to the drain contact. A positive voltage is applied to the source contact. c) Explain why current flow in a MOSFET transistor. Use a diagram to illustrate your answer.
1- a. For the circuits given below calculate the currents through the zener diode (V5.1V) and the current through the Si-diode. 1k Ohm 1k Ohm -10V 1k Ohm 12V b. The emitter of an NPN type BJT is connected to ground. Its base is connected to a 5V supply with a 10K resistor. Its collector is connected to the same supply with a 6K resistor. Calculate the range of ß such that the transistor is not saturated.
Draw the n-p-n silicon bipolar junction transistor at zero bias and also in forward active mode with an aid of the energy band diagram. Please ensure to draw with careful detail, reflecting the doping density in each region.
9
) Draw the Forward and reverse bias PN junction diagram using the following voltages (10V, -9V) and (-5V, OV) respectively (i1) Explain the operation of the above circuits.
A current-source bias circuit in the figure below has the following values: VDp = 10 V, Vee = -6 V, and Rg = 10,045,170 ohms. To produce a 13 mA drain current and a 7 V drain voltage, determine the value of Rp in ohms. Vpp Rp Rg RE -VEE
Choose whether the followings are True or False. 1. The MOSFET has 2 terminals Drain and Source. 2. An E-MOSFET operates in the depletion mode. 3. The LED emits light when reverse biased. 4. In the n-channel E-MOSFET, VGs(th) has a positive value. 5. A diode conducts current when forward biased and blocks current when reverse biased 6. An n-channel D-MOSFET with a positive Vcs is operating in the enhancement mode. 7. The varactor diode acts as a variable capacitor under forward bias conditions. 8. Once a BJT transistor is in the saturation, a further increase in base current will cause the collector current to increase. 9. In a given BJT transistor amplifier, Rc=2.2KQ and r'=20 Q then the voltage gain is equal to 110. 10. Voltage Amplification Av in a BJT is the output voltage divided by the input current
Determine the VDS and the drain current for the E-MOSFET circuit shown. The data sheet for this particular MOSFET gives ID(ON)=500 mA at VGS=10 V and VGS(th)=1 V.
b. [PI-3.a] Define electrochemical potential "p" and give the condition under which electrochemical potential p₁ at source junction of a MOSFET channel is equal to the electrochemical potential µ₂.
TEST Read the question carefully. Write the letter for each correct answer in the blank space provided. A 1. Maximum power is delivered from a source of power to a load when the a. load current is equal to the power source current b. impedance of the load is equal to the output impedance of the power source c. output impedance of the power source is high compared to the impedance of the load d. output impedance of the power source is low compared to the impedance of the load 2. The emitter follower is a (an) a. impedance matching device b. high gain voltage amplifier c. phase inverter d. combination power and voltage amplifier 3. The emitter follower uses a. no collector resistor b. a forward bias collector-base junction c. negative feedback (degeneration) d. an NPN transistor only 4. The emitter follower has output resistance. a. high, high b. low, low c. low, high d. high, low input resistance and 5. The current gain of an emitter follower is a. less than 1 b. equal to 1 c. greater…
In N-channel E-MOSFET, as the VGS increases positively, the Drain current decreases. True or false
........ (Figure-1) R. RB= 380kN,Rc= 1kN B = 100, VBB = Vcc=12V RB ww Vec CC ......... I, V CE СЕ V ВЕ BB Q-1-b) Describe briefly the input / output characteristics and application of Common Emitter BJT Configuration