An insulated piston–cylinder device contains 0.8 L of saturated liquid water at a constant pressure of 120 kPa. An electric resistance heater inside the cylinder is turned on, and electrical work is done on the water in the amount of 1400 kJ. Assuming the surroundings to be at 25 ºC and 100 kPa, determine (a) the minimum work with which this process could be accomplished and (b) the exergy destroyed during this process

Q: Two rigid tanks are connected by a valve. The left tank is filled with 8.6 ft of air initially at 22…

A: Given Pressure, PA = 22 psia               PB = 17.3 psia Volume, VA = 8.6 ft3               VB =…

Q: Devices can be combined to perform a variety of tasks. An adiabatic compressor, with air as the…

A: To find: The magnitude of power delivered to generator by turbine. Given: The temperature of the…

Q: Devices can be combined to perform a variety of tasks. An adiabatic compressor, with air as the…

A: To find: The magnitude of power delivered to generator by turbine. Given: The temperature of the…

Q: An insulated rigid tank contains 5kg of air (an ideal gas) at 25C and 100kPa. A paddle wheel inside…

A:

Q: A mass of 8 kg of helium undergoes a process from an initial state of 3.9 m³/kg and 15°C to a final…

A: Introduction The increase in usable work potential as the process moves from the beginning state to…

Q: One lbm of R-134a is expanded isentropically in a closed system from 100 psia and 100°F to 10 psia.…

A: Here we will refer to the refrigerant table to get the values of internal energy and entropy and use…

Q: Hot combustion gases enter the nozzle of a turbojet engine at 250 kPa, 650°C, and 70 m/s and exit at…

A: Given data as P1=250 kPaT1=650 °C=923 Kv1=70 m/sP2=80 kPaT2=420 °C=693 Km˙=1.2 kg/sQloss=90 kW=90000…

Q: Steam enters an isentropic turbine at 4 MPa. X percent (by mass) of the steam exits the turbine at…

A:

Q: Exergy Destruction during Expansion of Steam. A piston-cylinder device contains 0.05 kg of steam at…

A: Given   Mass, m = 0.05 kg   Heat, Q = 2 kJ           T1 = 300 K Find   Exergy destroyed, x…

Q: Steam enters an adiabatic turbine steadily at 4 MPa and 500°C at a rate of 6 kg/s and exits at 0.3…

A:

Q: pom has a 250 W re c resistance heater. iCe it is observed t

A:

Q: A closed system containing a gas undergoes a reversible process from 600 kPa and a volume of 0.15 m3…

A: Write the given values with the suitable variables. P1=600 kPaV1=0.15 m3V2=0.50 m3γ=1.4 Here, P1,…

Q: Refrigerant-22 absorbs heat from a cooled space at 50°F as it flows through an evaporator of a…

A: Given data as per question

Q: 2. During some actual expansion and compression processes in piston-cylinder devices, the gases have…

A:

Q: With a stirrer, the pressure of 15 grams of air has been raised adiabatically. enclosed in a rigid…

A:

Q: Air contained in a rigid volume of 0.5 m³ and initially at 400 kPa and 57°C receives 200 kJ of work…

A: Given data:

Q: Devices can be combined to perform a variety of tasks. An adiabatic compressor, with air as the…

A:

Q: For a closed system, show that the total work for a reversible adiabatic process, (PV^k = C) is…

A:

Q: In a piston-cylinder system, there is 3 kg of refrigerant-134a initially at 1.2 MPa and 50°C. The…

A: The mass of refrigerant is .The initial pressure of refrigerant is .The initial temperature of the…

Q: Refrigerant 134a was added into the repaired compressor. Subsequently, the inlet of the compressor…

A: Given data, Inlet condition of refrigerant (State 1):- Pressure = 0.1 MPa, Temperature = 30 °C Exit…

Q: Twokg of saturated water vapor at 600 kPa are contained in a piston–cylinder device. The water…

A: Given: The initial pressure is P1= 600 KPa. The pressure at expansion is P2= 100 KPa. The…

Q: For adiabatic steady-flow devices, the vertical distance Δh on an h-s diagram is a measure of work,…

A: In adiabatic steady-flow devices, the enthalpy remains constant, and the process is called as…

Q: Consider steady heat transfer through a 5-m 6-m brick wall of a house of thickness 30 cm. On a day…

A:

Q: Q1/B/ Refrigerant-134a is to be compressed from 0.14 MPa and 10°C to 0.4 MPa and 40°C steadily by a…

A:

Q: A clased system has water at 4 MPa and 400 °C, wnich undergoes an is0thermal reversible compression…

A:

Q: Oxygen gas is compressed in a piston–cylinder device from an initial state of 12 ft3 /lbm and 75°F…

A: Given data: The characteristic gas constant for oxygen is The specific heat at constant volume for…

Q: Three kilograms of water in a piston-cylinder assembly, initially at 100 kPa and 75°C, are heated at…

A: we know thatPV=mRTfor state 1,substitute 100kpa for P,m=3R=461.89j/k…