An instrumeht used to measure force in "N" has the following errors: Linearity error + 0.1 N Hysteresis error ± 0.2 N Sensitivity error + 0.05 N Zero drift 0.5 N If the instrument is used to measure a 100 N forces with 3 digits resolution, what is the instrument's design stage uncertainty?

Q: The adjocent figure ahowa the scales of a micrometer. If the vertical scale has 50 divisiona ond the…

A:

Q: Find the precision of the 4th measurement, from the values in the table below No Xn 1 48 2 50 3 52 4…

A: The accurate measurement will be the average value  Xnavg = (48+50+52+47+51)/5 = 49.6

Q: find the absolute uncertainty in d. d= (10^((m-M+5)/5))/10^6 m=13.78 M=-18.78 error in both m…

A: Since d is a function of m and M, which are two independent variables, the absolute uncertainty (δd)…

Q: er exercise 2: cy of the micrometer is O..50. mm mental error is 7of the sleeve scale&:00 wmm

A: Given: The accuracy of the micrometer is The instrumental error is.The reading of the sleeve…

Q: Using the trig. substitution 2 sin(θ) cos (θ) = sin(2θ), the range expression becomes: Range =…

A: Apply the first kinematic equation in the vertical motion to determine the time to reach the maximum…

Q: In a Measurement ,the Expected value is 56 V and the measured value is 52 V. Find (i) Absolute error…

A: Given  Expected value. Is 56 Measured value is 52.

Q: The equation used to estimate the Bluetooth distance range is given by: Where, D is the estimated…

A:

Q: MEASURED USING CENTIMETER RULER MEASURED USING CENTIMETER RULER   Measured Diameter d (cm) Measured…

A: Solution: Calculate the relative uncertainty in diameter for dime. ∆Uddime=0.051.76×100=2.84%…

Q: A reference mass of 50.00 Kg is weighted using a digital balance with 1% accuracy. The measurement…

A:

Q: How do you use the slope to determine "little g" from your experimental data? og = (4 Pi^2)/slope og…

A: Time period of the simple pendulum is given as,

Q: In an experiment four quantities a, b, cand d are measured with percentage error 1%, 2%, 3% and 4%…

A:

Q: An engineering function is given by a = y²e² cos x At x = 1.3,y = 2.1,and z = 4.9, compute the…

A:

Q: marathon runner completes a 42.188-km course in 2 h, 39 min, and 25 s. There is an uncertainty of 24…

A: Distance covered x = 42188 m                      Time t = 2 hr 39 min 25 s…

Q: Rank these SI distance units from smallest to largest: μm, am, fm, nm, mm, cm, m, km, Gm, Tm, Mm,…

A: Rank these SI distance units from smallest to largest: μm, am, fm, nm, mm, cm, m, km, Gm, Tm, Mm,…

Q: By measuring the acceleration due to gravity a student finds gA=(9.85+-0.08)m/s^2. A student B finds…

A: Note: You have posted a question with more than three subparts.  As per our policy, if nothing is…

Q: The coefficient of static friction between a block and a ramp is given by  μ = tan(θ)  where θ is…

A:

Q: Find the volume of a thin rectangular box (cuboid) whose sides are measured as 5.2 cm, 12.4 cm, and…

A: Given: Measurement of sides of cubiod are a=5.2 cm b=12.4 cm c=13.42 mm = 1.342 cm To determine…

Q: In an experiment to measure the value of pi, the following results are obtained for pi: 3.14…

A: The computation of percent error helps to determine how near a measured number is to a real value.…

Q: A traffic patrol officer uses a UAV with a camera to measure the transit time of vehicles between…

A:

Q: An instrument is used to determine the concentration of a chemical in water. The instrument signal…

A: Given : Relation between instrument signal "Z" and concentration of the chemical "C" Z = kC + P Z =…

Q: An infant’s pulse rate is measured to be (130.0 + 5.0) beats/min. What is the absolute uncertainty…

A: Given that:- Infant pulse rate=(130+5) beat/min

Q: The mass of an aluminum cube was measured to be (A)=71.2 g. Using the Vernier caliper, the length of…

A:

Q: A (An) ______________ measurement is one in which systematic errors are small.

A: Systematic errors are the errors introduced due to the inaccuracy of the measurement. This error is…

Q: A line was measured by EDM found 4032.32 m, what is the probable error in this distance if the EDM…

A: measured value = 4032.32 m Precision = ±(2 mm +3ppm)  To find = Probable error .

Q: When measuring a shaft with a specified diameter of 0.50 ± 0.01, what minimum descrimination should…

A: Given that, A shaft with a specified diameter of 0.50 ± 0.01. We need to find the minimum…

Q: The coefficient of static friction between a block and a ramp is given by μ = tan(θ)  where θ is the…

A: The objective of the question is to calculate the uncertainty of the coefficient of static friction…

Q: Find the absolute uncertainty for the volume of a rectangular prism with the following measure…

A:

Q: In a Measurement ,the Expected value is 72 V and the measured value is 63 V. Find (i) Absolute error…

A: (i) The absolute error is given by :  (ii) The relative error is given by :

Q: Given values: m1=10 kg, r1=75 cm, m3=15 kg, had to find r3=? I got r3=50cm m1 = 10 kg at r1 = 75 cm…

A: Please see the answer below

Q: A person measures his or her heart rate by counting the number of beats in 30s. If 40+1 beats are…

A: Given the number of beats is 40. And the uncertainty with beats is 1. The time is defined as 30 s,…

Q: A group of students are gathering data in a repeated measurement experiment. The collected data so…

A: Given data of measurement 4.2, 4.2, 4.2, 4.2, 4.2, 4.2 We have to calculate uncertainty of the…

Q: An error due to a poorly calibrated electronic equipment. (A) Instrument Error (B) Personal Error…

A:

Q: Please find the nominal value of A and the uncertainty in this term.

A: Nominal Value The nominal value of a variable, also known as the absolute value of the variable, is…