An instruction is located 314 bytes in a program with 6 pages. If a page is 128 bytes long, what are the page number and displacement values of the instruction? O Page: 3, Displacement: 58 bytes O Page: 2, Displacement: 58 bytes O Page: 2, Displacement: 45 bytes Page: 3, Displacement: 14 bytes

Q: PC is also called Data counter Instruction pointer Non of above File pointer Memory pointer

A:

Q: In simple words, describe the final data pointer register.

A: Solution: Data pointer register: It is a 16-bit register that can hold a total of two bytes' worth…

Q: Static memory allocation and dynamic memory allocation are two terms you should be familiar with.

A: The answer :

Q: EXPLAIN ALL STEPS: Determine the output of the following Pep/9 machine language program if the input…

A: Address   Instruction(in hex)0000         D1FC15Convert the instructions into binary…

Q: In the memory of Computer, if we say 256 * 8, it means 256 is size and 8 is Data bus size

A: The correct answer is memory size

Q: dataval1 BYTE 10hval2 WORD 8000hval3 DWORD 0FFFFhval4 WORD 7FFFh Write an instruction that subtracts…

A: an instruction that subtracts val3 from EAX:

Q: assembly code for  Write a program that writes 67D, 65D, 63D, ...... values to addresses from 22H…

A: The task is to write an assembly program that writes specific values to specific memory addresses…

Q: UL & DIV instruction in Assembly Language Table 1 EAX EBX ECX EDX 10H 20H 2H 0H Refer to…

A: It is defined as a low-level programming language for a computer or other programmable device…

Q: Assembley 68000 Question: Start with a small value in D0 and execute a loop that multiply D0 by…

A: Assembley 68000 Question: Start with a small value in D0 and execute a loop that multiply D0 by…

Q: 16-bit registers A and B hold 8-bit values x and y respectively. Write a program that moves these…

A: ; Move Value AX to CX register MOV CH, AL ; Move value from BL to CL, to move from 16 bit register…

Q: When a subroutine is called, the address of the instruction following the CALL instruction is stored…

A: Program Counter

Q: 8- The memory unit of a computer has 2.00E+20 words. The computer has instruction format with four…

A: I have given a handwritten solution in the below steps.

Q: his question is in assembly language: Code a Section of a Program Code a loop

A: 25 DUP(?) is identical as to write '?' (=any value) 25 times. Thus 'DB 25 DUP(?)' implies 'reserve…

Q: C PROGRAM FOR MICROPROCESSOR* Write a C program that will use 7-segement LEDS to display the number…

A: Answer:

Q: The instructions that are used to call a subroutine from the main program and return to the main…

A: Role of CALL is to call a subroutine and RET is used for returning to main.

Q: Looking at a line in a listing file: 0009 EB05 jmp test the second byte in the jmp test instruction…

A: Introduction

Q: why is it not a good idea to use numeric addresses when writing instructions that access variables?

A: Justification: Generally, the instructions are written in combination of uppercase and lowercase…

Q: The computer program is stored in the lowest 1kbyte block of memory. Give the start and end address…

A: 1) We have a computer program which is stored in lowest 1kbyte block of memory 2) Lowest 1kbyte…

Q: 18.The instruction that is used for finding out the codes in case of code conversion problems is a)…

A: EXPLANATION: XCHG stands for eXCHanGe. This instruction is used for the purpose of exchanging the…

Q: COVISHIELD dose carton holds 50 vaccine vials (100 doses). The dimension of the carton is 18.5 x 9.5…

A: Answer: I have given answered in the handwritten format

Q: In X86 Assembly language:   Write a procedure to check if a number is divisible by an other number…

A: Solution:   Write a procedure to check if a number is divisible by an other number:…

Q: Assume a CPU with a fixed 32-bit instruction length has the following instruction forma

A: a. Op code + mode = 7 + 5 = 12 bits, leaving 22 bits for the operands. With 3 registers,each uses 9…

Q: 1- Write a program in assembly language for the 8085 microprocessor to send 10 bytes of data located…

A: You are asked to write a program in assembly language for the 8085 microprocessor to send 10 bytes…

Q: True or false:  Temporal locality is the tendency for a program to access a memory address shortly…

A: Temporal Locality for program

Q: The memory location at address 00002001 contains the memory variable in binary form. What is the…

A: We are given a address and using memory we will see what is the value present at that memory…

Q: C++ LANGUAGE Dynamic Memory Allocation Practice I Write a program that swaps the values of X and Y…

A: The function malloc is used to allocate the requested size of bytes and it returns a pointer to the…

Q: 80x86 Intel Assembly language Write an assembly language to declare all the variables needed in the…

A: Lets see the solution in the next steps

Q: How many bytes of memory does an interrupt vector take up?

A: Task :- explain the memory taken by the interrupt vector.

Q: When the INT instruction executes, what is the first task carried out by the CPU?

A: Task carried during the execution of INT instruction INT is an assembly instruction for x86…

Q: Write on emu8086 platform a code that counts your name characters and department name characters and…

A: Below i have given the program:

Q: Memory 12200 12201 12202 12203 12204 Content %3D AA EE FF 22 What result is produced in the…

A: To find result for the following execution instruction. a. LEA SI, [DI + BX + 5] b. LDS SI,[200]