Answered: An inductive coil draws 10 A current…

An inductive coil draws 10 A current and consumes 1 kW power from a 200 V, 50 Hz ac supply. Determine: (i) impedance (ii) power

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.7P: Let a 100V sinusoidal source be connected to a series combination of a 3 resistor, an 8 inductor,...

See similar textbooks

Related questions

Q: Design a circuit to limit a 20 V rms sinusoidal voltage to a maximum positive amplitude of 10 V and…

A: A limiter circuit should be designed that limits a 20 V rms sinusoidal voltage to a maximum positive…

Q: An inductor of value 5.6 H is connected across 240 V, 109 Hz supply. Then the value of inductive…

Q: 1-Choose the correct statement for pure resistor connected across single phase AC supply. a.…

A: Resistance Voltage and current are in same phase I=V/R So both are in same phase.

Q: 6. A coil draws 1875 watts when connected to a 150 V DC source. It consumes 3072 watts when used on…

Q: Alternating voltage and current differ from direct voltage and current because alternating voltage…

A: We’ll answer the first question since the exact one wasn’t specified. Please submit a new question…

Q: citor is 3,2 micro voltage of the ge -. Frequency 100 Hz (b) what is the rr it when it is 100C

Q: When an impedance coil is connected to a 100 V, 60-Hz, ac supply, the circuit current is 1 A. When…

Q: A coil draws 1875 watts when connected it a 150 V DC source. It consumes 3072 watts when used on…

A: Given:- When connected to DC supply, Inductance of coil acts as short circuit, only resistance of…

Q: A 120 V, 60 Hz power source is connected across an 800 ohm resistance in series with an unknown…

Q: Choose the correct statement for pure inductor connected across single phase AC supply. a. Current…

Q: triangle waveform with following specifications in Table B1. Table B1 RMS Voltage 50mV Number of…

A: In this question , we will make triangular waveform with given data and also find secondary current…

Q: Design a circuit to limit a 20 V rms sinusoidal voltage to a maximum positive amplitude of 10 V and…

A: Clipper Circuits:- A clipper circuit is used to clip the input voltage at a fixed higher and lower…

Q: An inductor is connected in parallel with a 6540 resistor and a function generator. The applied…

A: Let current through the resistor be IR and current through the inductor is IL and I be total source…

Q: For figure (1)draw and calculate the voltages waveform across each half of secondary winding and…

A: The figure shows a full wave rectifier circuit using two diodes D1 and D2. The supply voltage is…

Q: This is a photo of a capacitor that corrects the power factor in an AC setup, in DC it is used in…

A: Capacitor: It is an element used to store electrical energy in the electrical field. A capacitor is…

Q: 5. An alternating current varying sinusoidally with a frequency of 50 Hz has an rms value of 20 A.…

A: The solution is given below

Q: If there is reactive power associated with a circuit element we can say a) That said element is…

A: Real Power: The power dissipated from the supply is utilized by the resistive nature of the circuit.…

Q: Draw the sinusoidal waveform of the AC voltage and current for the given loads below. Describe the…

Q: shown in the Vps low is Write the FORMULA for the total impedance of the circuit Zut= R²+ cL- Write…

Q: 2. Refer to the Figure 2. a) Determine the total impedance of the circuit in polar form. b)…

A: Given

Q: 1.6. The resistance of a coil is 140 and its inductance 0.85 H. Determine the current, the p.f. and…

Q: The ripple factor for pure dc is Answer:

A: Ripple factor is ratio of ripple voltage to average voltage Ripple factor =ripple voltageaverage…

Q: Q1: Explain in detail, the power factor and its value for the following AC circuits ahown figure…

A: To solve above problem, one should have basic idea about working of AC circuits. In ac circuits…

Q: An inductor of 150hms and resistance of 10 Ohms are connected in series to a 230V, 50 Hz ac supply.…

Q: An inductor and a 470 ohm resistor are connected in series with a function generator. The current is…

A: Given, Resistor and inductor are connected in series. Resistance (R)= 470 ohm Current flows…

Concept explainers

Power Measurement

According to Blondel's theorem, the total power is measured with one less number of wattmeters than the number of wires present in the system. So, a single-phase and two-wire system will require one wattmeter and a single-phase and the three-wire system will require two wattmeters, and a three-phase and the three-wire system will also require two wattmeters and a three-phase and the four-wire system will require three wattmeter devices. The wattmeter is a device that measures power using one voltage and one current input as shown in the above figure. Multiple current or voltage input pair cables are used by many power analyzers and digital storage oscilloscopes (DSOs) for measuring watts, in effect within a single instrument acting as multiple wattmeters. It is possible to measure three-phase and four-wire power with one correctly specified power analyzer.

Question

An inductive coil draws 10 A current and consumes 1 kW power from a 200 V, 50 Hz ac supply.

Determine:

(i) impedance

(ii) power factor

(iii) reactive and apparent power.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Question is in the picture.
2, In a circuit, the capacitance of a capacitor is 3.2 microfarads and the rms voltage of the generator is 50 volts. Frequency (a) 100 Hz and (b) what is the rms current in the circuit when it is 1000 Hz?
6. A coil draws 1875 watts when connected to a 150 V DC source. It consumes 3072 watts when used on 240 V, 60 Hz AC source. Find the inductance of the coil. Ans. 0.0239 H
If there is reactive power associated with a circuit element we can say a) That said element is purely resistive. b) That said element has a unitary power factor c) That said element has associated electric or magnetic fields d) None of the above
Hskjswhjdbd
1.6. The resistance of a coil is 140 2 and its inductance 0.85 H. Determine the current, the p.f. and the circuit impedance when the coil is connected to 120 V, 60 Hz supply.
The ripple factor for pure dc is Answer:
1-Choose the correct statement for pure resistor connected across single phase AC supply. a. Current and Voltage are in phase b. Current leads the supply voltage by 90° c. None of these d. Current lags the supply voltage by 90° 2-Identify the current through the inductor in a RL transient circuit connected across DC voltage, when the switch is kept open. a. 0 b. Infinity c. V/R d. 1
An inductor of value 5.6 H is connected across 240 V, 109 Hz supply. Then the value of inductive reactance is ohms. 7666.62 1220.80 1916.66 3836.80
An alternating current varying sinusoidally with a frequency of 50 Hz has anrms value of 20 A.a) Determine the instantaneous value at 0.0025 seconds.b) Determine the instantaneous value, 0.0125 seconds after passingthrough a positive maximum value.c) At what time, measured from a positive maximum value, will theinstantaneous current be 14.14 A?
QUESTION 11 An inductor is connected in parallel with a 6540 resistor and a function generator. The applied voltage is 42V RMS and the total current is 67mA RMS. Find the magnitude of the current through the inductor. Enter your answer in the space provided. Round your answer to one decimal place. Your answer should be in mA but do not enter the unit.
2.2 please