An incompressible fluid flows in a linear porous media with the following properties L= 2500 ft K= 105 md P1= 2100 psi h = 22’ Φ = 16% P2 = 2090 psi Width = 310’ µ = 2 cp Calculate: 1. Flow rate in bbl/ day 2. Apparent fluid velocity in ft/day 3. Actual fluid velocity in ft/day

Q: • What is the average velocity of air in the duct? • Assume that the inner surface of the duct is…

A:

Q: What would be the rotation rate (in rad/sec) if during rotation the water in the right leg (with a…

A: As we know that, Increase in pressure head due to rotation with ω, at distance r from the axis is :-…

Q: You are designing a system to pump liquid methane at a temperature of 100 K from a storage tank to…

A: Given: The methane temperature, T = 100 K The discharge pressure at pump, P = 60 kPa The density of…

Q: In an open vessel, a certain volume V of water is perfectly agitated by means of an impeller 20 cm…

A: Diameter of the impeller, D=20 cm,Speed of the impeller, N=150 rpm,Density of water, ρ=1000 kg/m3…

Q: A system is to be thermally isolated. We have two options for that: which one would you choose?

A: Isolated system in thermodynamics  It is system is said to be isolated when there is no exchange of…

Q: During the opening of a valve in :pipe line, the flow is Uniform. O Steady. O Unsteady. O none of…

A:

Q: A steel plate 30 mm thick with a thermal conductivity k = 50 W/m K has a heat transfer rate of 125…

A: Note: As per policy we can solve the first question from your choice from multiple questions. Please…

Q: A piston-cylinder is producing a viscous oil flow, which has the flow rate of Q, radius R=1.5 mm,…

A:

Q: Using Buckingham Pi theorem to find the coefficients of equation: Pi=[density, running speed,…

A: π=ρa1Nb1Dc1μ

Q: Fluid, in P₁ = 2500 kPa P₂ = negligible Q₂ = 0.10 m³/s Pfluid=719 kg/m³ Hfluid=2.92 x 10-4. Epipe =…

A: Inlet PressureAnd outlet pressureDensity of the fluidDynamic viscosity of the fluidAnd elevation at…

Q: dv dy

A: first of all find out the shear stress = force/ Area. then apply newtons law of viscosity.for…

Q: Consider the flow of a fluid between point 1 and 2. Compute the direction of flow, whether the fluid…

A: At point 1,The pressure, P1 = 1.25*105 PaThe cross-sectional area, A1 = 15*10-4 m2The fluid…

Q: A water pump increases the pressure of the water passing through it. The flow is assumed to be…

A: On using mass conservation in the inlet and outlet of the pump, (a) In this case, Dout < Din…

Q: Consider a pressure transducer connected to a pipe through a connecting tube of diameter 3.5 mm and…

A: Givend=3.5mmL=50mmμ=0.001 Pa.St=7sC=25×106 mm3/bar=25×106 mm3/105Pa=250 mm3/Pa

Q: If the inlet diameter of the holding tank is 35cm and the outlet diameter is 30cm and the diameter…

A:

Q: Question 25 U-4m/s Po Ultimate width link to image) A pitot static probe in a uniform air flow of 4…

A: given data;freestream velocity (U)=4m/swidth (b)=7mm(a)location of the leading edge at the probe is…

Q: Using the velocity distribution for a laminar, incompressible flow of a Newtonian fluid in a long…

A: Given, Density of the fluid = ρ = 300 kg/m3 Dynamic viscosity of the fluid = μ = 1 x 10-4 Pa-s Cross…

Q: Figure 2. Determine the pressure at point I if: a) Viscous effect is neglected b) The only losses…

A:

Q: Determine required input power to motor [1.64 kW]

A: As per policy, we can solve the first problem from multiple questions.

Q: 7. Using the velocity distribution for a laminar, incompressible flow of a Newtonian fluid in a long…

A: Given, Fluid density = ρ = 300 kg/m3 Dynamic Viscosity = μ = 1 x 10-4 Pa-s Cross sectional area of…

Q: Water is discharged to the atmosphere through the fitting shown where the angle 8=45 degrees.…

A:

Q: 49. Water flows at a rate of 200 GPM into a piping system connected in series. Length, diameter, and…

A: Given:To find:(a) Total pressure drop.(b) Diameter of the equivalent pipe.

Q: mechanics of fluids estimate the characteristics of hydraulic devices utilized in force…

A:

Q: A piston-cylinder is producing a viscous oil flow, which has the flow rate of Q, radius R=1.5 mm,…

A:

Q: An incompressible fluid flows confined between two parallel, horizontal surfaces. The top surface is…

A: Given: To find : Velocity profile

Q: The rate mass of a fluid is 12 grams/s, is flowing in a tube at 0.9 m/s and it has a density of 1.7…

A:

Q: Dm = a shaft with a diameter of 75mm Dy = 75.150mm in diameter and L = Its viscosity is 0.15 kg /…

A:

Q: 6. A water jet of cross-sectional area A with a velocity U, and density p causes a cart to move at a…

A:

Q: The velocity distribution in a 0.02 m diameter horizontal pipe conveying carbon tetrachloride…

A:

Q: 3- Consider the following 1D reservoir, where steady state, single phase oil flow takes place. This…

A:

Q: Estimate the depression "h" of mercury (S=13.6) in the capillary tube shown in the figure below.…

A:

Q: A plate 0.05mm distance from a fixed plate moves at 1.25 m/s and required a force per unit area of 3…

A:

Q: LUID MECH & THERMODYNAMICS, 6e, S.L. Dixon, C.A. Hall (The answer is available in Chegg, but I do

A: a We will start writing the expression for loss in total pressure across a compressor cascade due to…