An inclined venturi meter has an entrance of 0.08 m in diameter and throat of 0.02 m in diameter. Calculate the coefficient of discharge when the pressure difference between the entrance and the throat is 173kN/m^2. The venturi meter used to measure the discharge of the 311 dm^3/minute. Throat is 0.46m higher than the entrance.

Q: In the system shown, the water discharge flow rate of 0.0025 m³/s is delivered through the 8 cm…

A: Given data: ◆ The diameter and length of the cast iron pipe: D = 8 cm = 0.08 m , L = 388 m ◆ The…

Q: Recommend the low cost flow meter used in industries for measuring flow that provides negligible…

A: Reynold number is the ratio of inertia forces to the viscous forces. Reynold number signifies the…

Q: There are three pipes and each has different friction or roughness factors below

A:

Q: A sharp edge orifice 90-mm diameter, in the side of a tank having 3 horizontal cross-section 2.3m…

A: Given: The diameter of orifice, d = 90 mm the side of square section, s = 2.3 m The rate of inflow,…

Q: (b) The throat and full bore diameters of a venturi meter are 18mm and 55mm, respectively. The…

A: Given data: Let us consider suffix 1 and 2 for the full bore and throat section respectively. ● The…

Q: The blades on the radial-flow pump shown in (Figure 1) rotate at w = 200 rad/s. The blades are 2 in.…

A:

Q: b) A rotameter uses a cylindrical float 0.02 m in height and 0.02 m in diameter, with proper density…

A:

Q: Explain the operating principles of a venturi flowmeter. Derive the flow equation.

A:

Q: An inclined venturi meter has an inlet diameter of 0.075 m and 0.019 m diameter at the neck. If the…

A: Given:Inlet diameter, d1=0.075 mNeck diameter, d2=0.019 mThe pressure difference, P1-P2=175.5…

Q: Estimate the flow rate in gallons per minute from a 12 inches diameter pipe when the water velocity…

A:

Q: coefficient of discharge=

A: Given: h1=314 mm h2= 286 mm Q=165 ltter/s A1=338.6 mm2 A2=84.6 mm2 To determine: The coefficient of…

Q: A Venturi tube is to be used to measure a flow rate of water in a 120mm pipe. The maximum flow rate…

A:

Q: The venturi meter experiment observation readings are 304 mm, 286 mm, and the flow meter reads 166…

A: Given,h h1=304 mm=0.304 mh2=286 mm=0.286 m Q=166 liter/hr=166×0.0013600 m3/s=4.611×10-5 m3/s…

Q: The flow rate of water of mass density of 998 kg/m^3 and viscosity of 1.002 x 10^-3 kg/m-s, through…

A:

Q: Water enters a pipe of diameter 22 mm with a venturi meter with a throat diameter of 12 mm. At the…

A:

Q: The flow rate of water at 30.7 oC in a 3.31 inch inner diameter steel pipe is measured by an orifice…

A: Pipe diameter, D = 3.31 inch Orifice diameter, d = 0.89 inch It is asked to find the diameter ratio…

Q: The theoretical flowrate calculated for a venturi meter is 0.0001895 m3/s. The actual flowrate…

A:

Q: A venturi-meter having an entrance diameter of 300 mm and throat diameter 200 mm is used to measure…

A:

Q: CHOOSE THE CORRECT ANSWER! Three pipes of 400 mm, 350 mm and 300 mm diameter are connected in…

A: To find: The flow in pipe 3. Given: The diameter of the pipes are d1=400 mm1 m1000 mm=0.4 m, d2=350…

Q: (b) The throat and full bore diameters of a venturi meter are 18mm and 55mm, respectively. The…

A: To find: The theoretical discharge through the venturi meter. Given: The throat diameter of a…

Q: A pumped fluid distribution system is being designed to deliver 400 gal/min of water to a cooling…

A: Given: The flow rate, Q = 400 gal/min The pipe type = schedule 40

Q: The flow rate of water of mass density of 998 kg/m^3 and viscosity of 1.002 x 10^-3 kg/m-s, through…

A:

Q: The venturi meter experiment observation readings are h2= 283 mm, h1=307 mm, and the flow meter…

A:

Q: QUESTION 2 A vertical circular tank that is 1.5 m high, has sloping sides. The tank is 50 m and 30 m…

A:

Q: Water flows through two different pipes A and B of the same circular cross-section but at different…

A:

Q: An orificemeter with ortfice diameter 12 cm is inserted in a pipe of 20 cm diameter. The pressure…

A: Given Data, d0=12 cm=0.12 m (orifice)d1=20 cm=0.2 m (pipe)p1-p0=9.81 N/cm2Cd=0.6

Q: A venturi meter with a throat diameter of 100 mm is fitted in a vertical pipeline of 200 mm diameter…

A:

Q: The venturi meter experiment observation readings are 319 mm, 283 mm, and the flow meter reads 178…

A:

Q: What is the entrance length in a 4-cm-diameter pipe if 0.5*10^ -4 m^ 3 / s water is flowing

A:

Q: A venturi meter has an inlet diameter of 65 mm and a throat diameter of 26 mm. When measuring the…

A:

Q: A fan has a suction static pressure of 40mm of water vacuum with air velocity of 5m/s. The discharge…

A:

Q: The venturi meter experiment observation readings are 309 mm, 286 mm, and the flow meter reads 170…

A:

Q: An oil of specific gravity 0.89 is flowing through a horizontal venturimeter fitted to a 242 mm…

A: Given, specific gravity of the oil , S =0.89 Diameter of the pipe , D =242 mm = 0.242 m Diameter of…

Q: hsllo

A: Given: The specific gravity of petrol is, ρp=0.81. The specific gravity of oil is, ρm=13.6. The…

Fluid Dynamics

The study of the flow of gases and liquids, usually in and around solid surfaces, is known as fluid dynamics in physics and engineering. Fluid dynamics, for example, can be used to evaluate the movement of air through an airplane wing or the surface of a vehicle. It can also be used in ship design to increase the speed at which ships pass through water.