An ideal vapor-compression refrigeration cycle that uses refrigerant-134a as its working fluid maintains a condenser at 700 kPa and the evaporator at -13.5 °C. Determine this system's COP and the amount of power required to service a 100 kW cooling load. 3 4 Warm environment Он Condenser Expansion valve Evaporator 000 (2) W; Compressor 1

Q: Draw isometric projection of casting, two views (FV and TV) of which are shown in figure in First…

A: Refer the following image for the the required rough sketch of isometric view of the given…

Q: 127 157 18 11 0) D 24y

A: Let's name the marked lengths in the given figure for calculation purpose.

Q: Draw the isometric projection For the Shapes Shown Below, Using Scale (1:1)

A:

Q: 60 10 20 45 35 15 30 2Holes DIA 20 20 60 10 120 30 15

A: Given :-  Orthographic view Draw :- Front view  Top view and Right side view

Q: draw isometric diagram with measurement labels

A:

Q: Q3 Draw Front, Top and side view of the drawing shown below. All dimensions in mm and scale 2:1. 18…

A: Orthographic Projection It is a form of presenting a three-dimensional object into Two dimensional.…

Q: What is the weight of 12 kilogram object, expressed in lbf? 26.424 o lbf

A: Recall:- 1 kilogram = 2.20462 lbf  Weight of the object (W) = 12 kilogram

Q: Using the drawing below identify th mistake on dimensioning rules and write the correct method to…

A: According to DG&T standards, there are 5-dimensional mistakes that are highlighted in the fig…

Q: Can you please send me top,front and right view of the given diagram with correct dimensions.

A: The isometric view is given in the diagram.

Q: Do four colors really suffice? Suppose this map shows the provinces of a country. peculiarity of…

A: The four colour theorem, also known as the four colour map theorem, claims that no more than…

Q: for this question just sketch what it should look like:

A: Note : Window is denoted by point P

Q: Describe the differences between the three major categories of pictorial views we learned about.…

A: Hi, You have submitted more than one question but according to guidelines, we will solve first…

Q: ect with dimension. mode 50 R20 Ø20 25 15 Ø32 Ø60 80 45 50 60

A: According to the details provided in the question, we need to DRAW the half sectional view of the…

Q: Based on the following orthographic projections for each object, generate a full-scale isometric…

A: Isometric projection Isometric projection is a method for representing three-dimensional objects…

Q: Q5: For the below shaded area, calculate kand Kr 130 mm 30 mm 30 mm 40 mm 40 mm

A:

Q: SolidWorks to create the parts.

A: I am using Solidworks to draw a 3-d object of the given problem.

Q: Hello, I need help with the answer of 3.14 from the picture, please.

A:

Q: Fill-up the blanks in the following sentences by appropriate words selected from the list of words…

A: As per the regulations of the Company, only three parts will be answered, and for rest of the parts…

Q: Use the following isometric drawing of a hospital to create a two-point perspective drawing. (Use an…

A: Use the following isometric drawing of a hospital to create a two-point perspective drawing. (Use an…

Q: 2. Given the multiview drawing set, create an isometric sketch. Use the front view as the lower left…

A: Answer:  ISOMETRIC VIEW OF THE GIVEN PROBLEMFor a step-by-step solution have a look through the…

Q: make a three-view drawing, complete with dimensions, of the part. Show the dimensions with the view…

A: the given isometric view

Q: Draw isometric view of casting, two views (FV and SV) of which are shown in figure in First angle…

A: Given question: Draw isometric view of casting, two views (FV and SV) of which are shown in figure…

Q: Q. 1: A cast iron bracket subjected to bending has a cross-section of I-shape with unequal flanges…

A:

Q: Q3/ Draw the front section of the figure (2)? RIO p10 54 p82 $56 76 RI14 FROM ト!2 CENTRE OF BOSS $12…

A: Solution:   The front section of the figure is shown below:

Q: A wind turbine is rotating at 15 rpm under steady winds flowing through the turbine at a rate of…

A: Given:Speed of turbine, N=15 rpmMass flow rate of air, m=42,000 kg/sTip velocity of turbine, v=250…

Q: Make an Isometric Drawing of the support bracket shown in Figure 4. Take the dimension 'H' as 35 mm.…

A:

Q: 2 views are given (front and top), left view is requested. You also need to dimension the drawings.…

A: according to the given details in the question. left side view given below

Q: Draw Front and Side and top with all dimensions please

A: According to the question,A  3-D object is provide, we need to draw three projection views of the…

Q: Round off the following number to three significant figures:68.534s

A: The given no. is 68.534 s The given no. is having 5 significan figures as the number of digits are…

Q: 64 61 64 51 114 3 38 64 822 R32

A: The Front View, Top View and Right hand side view is given below.

Q: Use creo parametcric 4.0 drawing to Sketch all the compulsary part and partial views, including…

A:

Q: I need these three parts answered, if you are unable to answer all three parts please leave it for…

A: 4.The number 81073 denotes the CAGE no. as shown in the print. The CAGE code indicates Commercial…

Q: Draw the right side elevation of the object with the given top and front elevations below

A:

Q: Determine the torque (in N-m) applied to the shaft of a car that transmits 450 hp and rotates at a…

A:

Q: Draw the top, front, and side view with dimensions. (Third angle view).  Hint: You may draw the…

A: Find Draw the top view, front view, and side view of the given object.