An ideal Otto cycle has a compression ratio of 8. At the beginning of the compression process, air is at 103 kPa and 27°C, and 1850 kJ/kg of heat is transferred to air during the constant-volume heat-addition process. Accounting for the variation of specific heats of air with temperature, determine (a) The maximum temperature and pressure that occur during the cycle (b) The net work output (c) The thermal efficiency

An ideal Otto cycle has a compression ratio of 8. At the beginning of the compression process, air is at 103 kPa and 27°C, and 1850 kJ/kg of heat is transferred to air during the constant-volume heat-addition process. Accounting for the variation of specific heats of air with temperature, determine (a) The maximum temperature and pressure that occur during the cycle (b) The net work output (c) The thermal efficiency

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A gas turbine for an automobile is designed with a regenerator. Air enters the compressor of this engine at 100 kPa and 30°C. The compressor pressure ratio is 8, the maximum cycle temperature is 800°C, and the cold airstream leaves the regenerator 10°C cooler than the hot airstream at the inlet of the regenerator. Assuming both the compressor and the turbine to be isentropic, determine the rates of heat addition and rejection for this cycle when it produces 105 kW. Use constant specific heats at room temperature. The properties of air at room temperature are cp = 1.005 kJ/kg-K and k=1.4. Compressor Heat exchanger Comb. 4+ Turbine The rate of heat addition for this cycle is The rate of heat rejection for this cycle is - kW. kW.
A gas turbine uses two compression and two expansion stages, each stage having a pressure ratio of 4. The working fluid is intercooled between the two compression stages and reheated between the two expansion stages. Air enters the gas turbine at 100kPa and 17°C. The combustion chamber and reheat stage each contribute 300kJ/kg of heat. A regenerator uses exhausted gases to increase the working fluid temperature prior to the combustion chamber by 20°C. Assume constant thermal properties of air evaluated at 300K during your solution. Assume all turbine and compressor stages are isentropic. Draw the T-s diagram based on the numbering convention in the schematic below. Determine the system's thermal efficiency. Determine the required air mass flow rate to obtain an output of 10MW. 26 REMEWS REHEAT JNTER. Ti C2 Come REGEN. Scannad wim Camirwner
An ideal Diesel cycle has a maximum cycle temperature of 2000°C. The state of the air at the beginning of the compression is P = 95 kPa and T₁-15°C. This cycle is executed in a four-stroke, eight-cylinder engine with a cylinder bore of 10 cm and a piston stroke of 12 cm. The minimum volume enclosed in the cylinder is 5 percent of the maximum cylinder volume. Determine the power produced by this engine when it is operated at 1400 rpm. Use constant specific heats at room temperature. The properties of air at room temperature are cp=1.005 kJ/kg-K, cy=0.718 kJ/kg-K, R= 0.287 kJ/kg-K, and k=1.4. The power produced by this engine is 603 KTV. 2 W 3 E 4 R T U FB F9 0
An Otto cycle with a compression ratio of 8 begins its compression at 94 kPa and 10°C. The maximum cycle temperature is 900°C. Utilizing air-standard assumptions, determine the thermal efficiency of this cycle using constant specific heats at room temperature.
A Carnot engine using 1lbm air has the following conditions: heat addition beginning at 2200 psia and 22000R and continuing until the pressure is 1400 psia; isothermal compression from 14.7 psia and 5400R and continuing until the pressure is 23.1 psia. Determine (a) the heat transfer into the cycle; (b) the heat transfer from the cycle; (c) the work for each of the processes; and (d) the cycle efficiency.
A steady-state gas turbine is using air as the working fluid has shaft power output of 55 MW. Air enters the turbine at 300 K and leaves at 600 K and 30 m/s. The air is first compressed by adding a compression power of 15 MW. Then air receives 173 MW as heat input from the combustor. Determine the mass flow rate of air in kg/s.
Answer the question.
A steady-flow Carnot cycle uses water as the working fluid. Water changes from saturated liquid to saturated vapor as heat is transferred to it from a source at 245°C. Heat rejection takes place at a pressure of 10 kPa. Determine the amount of heat rejected. Use steam tables. The amount of heat rejected is 2404 kJ/kg.
A 4 cylinder Otto cycle engine has a compression ratio of 8. Inlet air is at 100 kPa and 17°C, and 800 kJ/kg of heat is transferred to the engine. Determine (a) the maximum temperature and pressure that occur during the cycle, (b) the net work output, (c) the exhaust gas temperature (d ) the mean effective pressure for the cycle.