Solve it correctly please. I will rate accordingly. An ideal Diesel cycle has a compression ratio of 16 and a cutoff ratio of 1.5.Determine the rate of heat addition. Take the input power to be 150 kW and the ratio of thespecific heats to be 1.4.a) 210.6 kWb) 201.4 kWc) 626.3 kWd) 234.4 kWe) 183.8 kWf) 186.3 kWg) 192.9 kWh) 191.6 kW

Answered: Image /qna-images/answer/e1997a76-dc82-4c51-806a-6e7c24af04ab.jpg

Answered: An ideal Diesel cycle has a compression…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Please solve it correctly , Don't Use Ai tool. (1) A twist drill bit is used to drill a hole of diameter 2.0 at 4578.1 rpm at a feed rate of 2.5 in/min. Calculate the MRR in in^3/min. Take "pi" = 3.14. Round your answer to the nearest tenth.
Two gears mounted on shafts have 10 and 15 teeth, respectively. The center distance is 10 inches. The addendum equals the module, and the clearance equals 0.135 times the module. Determine (a) pitch diameters, (b) addendum, (c) dedendum, and (d) root circles. Draw simple circles showing the diameters and the center distance. Complete solution and drawing is required.
A helical gear of 10 inches pitch diameter has a helix angle of 25 degree, and there are 35 teeth. The gear transmits 40 hp and rotates at 450 rpm with a normal pressure angle of 20 degrees. Find the axial force transmitted by the gear. A 252.26 lb B 225.26 lb C 522.26 lb D) 552.26 lb
The spur gearing arrangement made of two parallel shafts,whose pitch circle diameters of driven and driver gears are 84cm and 35cm respectively. If driven shaft runs with 10 r.p.s,determine the following; 1. Center distance between the two shafts in mm. 2. Speed of driver shaft in rpm 3. Velocity ratio 4. Number of teeth's on driver and driven shaft for the given module 6mm
I need the answer quickly
MECHANICAL ENGINEERING UPVOTE WILL BE GIVEN. PLEASE WRITE THE COMPLETE SOLUTIONS LEGIBLY. SHOW THE STEP-BY-STEP PROCESS WITH SHORT COMMENT/EXPLANATION. ANSWER IN 4 DECIMAL PLACES. Determine the torque (in N-m) applied to the shaft of a car that transmits 450 hp and rotates at a rate of 3000 rpm.
A motor is driving an output shaft through a single-stage gears, as shown. Input Gear, N, Motor To Output Gear, N2 Number of teeth of the input gear, N1 = 24; Number of teeth of the output gear, N2 = 48; Gear efficiency = 95%; %3! If the output shaft is to deliver torque To = 20 Nm, calculate the torque required on the input shaft, Ti. Give your answer in Nm to 1 decimal places.
73 alll & O... Q1:- The objective of the gear train is to calculate:- 17 responses Speed ratio Number of gear 29.4% teeth The applied torque 5.9% All of these None of these 58.8% Q2:- The speed ratio of a compound gear train can be obtained by using the following Copy chart formula:- 17 responses Product of teeth on driven gears divided by the 11.8% product of teeth. Product of teeth on driver gears divided by the product of teeth. 5.9% Product of teeth in driven aears
1. A 5 in diameter solid shaft is used to drive the propeller of a marine vessel. It is necessary to reduce the weight of the shaft by 60%. What would be the dimensions of a hollow shaft in mm if made of the same material as the solid shaft?
1)In a simple micrometer with screw pitch 0.5 mm and divisions on thimble 50, the reading corresponding to 5 divisions on barrel and 12 divisions on thimble is
Calculate to the correct number of significant figures. 89.3x77.0x0.08
Answer the attached file

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

An ideal Diesel cycle has a compression ratio of 16 and a cutoff ratio of 1.5. Determine the rate of heat addition. Take the input power to be 150 kW and the ratio of the specific heats to be 1.4.