An FM Signal operates with a value for Frequency Deviation, (Af) and a Modulating Frequency, (fm) as explained below. The Total Power (PT) and its Resistive Load (RL) is also outlined below.. Given the Carrier Frequency is in unit of Mega Hertz (MHz). The specifications of the above FM Signal are as the followings Frequency Deviation, (Af)= 6 kHz Modulating frequency, fm 2 kHz Total Power, PT = 4.5 W Resistive Load = 50 2 Carrier Frequency 150 MHz Determine the followings a) Signal voltage, VT in RMS b) Modulation Index, m OK Now Please Refer to Bessel Table. c) Based of Modulation Index, m calculated in (b), determine the value of Jo for the Carrier and J1, J2 and Ja for the first three sets of sidebands. i) Jo

An FM Signal operates with a value for Frequency Deviation, (Af) and a Modulating Frequency, (fm) as explained below. The Total Power (PT) and its Resistive Load (RL) is also outlined below.. Given the Carrier Frequency is in unit of Mega Hertz (MHz). The specifications of the above FM Signal are as the followings Frequency Deviation, (Af)= 6 kHz Modulating frequency, fm 2 kHz Total Power, PT = 4.5 W Resistive Load = 50 2 Carrier Frequency 150 MHz Determine the followings a) Signal voltage, VT in RMS b) Modulation Index, m OK Now Please Refer to Bessel Table. c) Based of Modulation Index, m calculated in (b), determine the value of Jo for the Carrier and J1, J2 and Ja for the first three sets of sidebands. i) Jo

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Problem 5. A carrier wave of frequency 20 MHz is frequency-modulated by a sine-wave of amplitude 2 volts and frequency 4 kHz. The frequency sensitivity of the modulator is 10 kHz per volt. a) Determine the approximate bandwidth of the FM wave using Carson's rule. b) Repeat part (a) assuming that the amplitude of the modulating wave is doubled. c) Repeat part (a) assuming that the modulation frequency is doubled.
A Phase Modulator has a phase deviation constant, Kp = 35°/V. The carrier signal is ec = 8 cos2n(800k)t, volts and the modulating signal is em = 5 sin2r(2000)t, volts. a. What is the equation of the PM signal? b. What is the maximum phase deviation? c. what is the amount of deviation in the carrier phase angle at t = 160µs?
What is RF?
Problem 4. A carrier wave of frequency 25 MHz is frequency- modulated by a sine-wave of amplitude 3 volts and frequency 4 kHz. The frequency sensitivity of the modulator is 12 kHz per volt. a. Determine the approximate bandwidth of the FM wave using Carson's rule. b. Repeat part (a) assuming that the amplitude of the modulating wave is doubled. c. Repeat part (a) assuming that the modulation frequency is doubled.
it is the fractional value of an AC quantity through which the .6 * .AC quantity has advanced or delayed from the reference point frequency period Peak-to-peak value Phase different phase O
Q3: A sinusoidally modulated AM waveform is shown below, Determine: 1. Peak amplitude of the upper and lower side frequencies. 2. Peak amplitude of the unmodulated carrier. 3. The modulation index and it is percentage. 4. The total power and the power efficiency. 5. Plot the frequency and the power spectrum of the modulated signal if the frequency of the carrier and the modulating signal are 2MHz and 15KHz respectively. 12 6 0 -6 -12 T
100 MHz carrier wave has a peak voltage of 5 volts. The carrier is frequency modulated (FM) by a sinusoidal modulating signal or waveform of frequency 2 kHz such that the frequency deviation Af is 75 kHz. The modulated waveform passes through zero and is increasing at t= 0. Determine the expression for the modulated carrier waveform.
An AM signal is provided below. The carrier frequency is 500 Hz, and the modulating signal is a single-tone sinusoidal signal. The x-axis is in time while the y-axis is the amplitude of the AM signal. Answer the following questions with appropriate solutions if applicable. Determine the type of AM signal in the figure. Determine the frequency of the message signal in Hz. Determine the peak voltage level of the carrier in V. Determine the peak voltage level of the modulating signal in V. Determine the modulating index. Determine the power of the unmodulated carrier in W. Assume the load resistance to be 1-ohm. Determine the power of sidebands in W.
modulating signal amplitude wideband FM dependent %m carrier swing Prompts Submitted Answers It determines the rate of frequency shift Choose a match frequency deviation The peak to peak frequency deviation Choose a match narrowband FM FM with modulation index between 1 and 10 Choose a match modulation index The ratio of actual frequency deviation to the maximum Choose a match modulating frequency allowable frequency deviation expressed in percentage. midband FM Frequency deviation of the carrier is to the Choose a match amplitude of the modulating signal. proportional inverse proportional
Q2. An angle modulated signal with a sinusoidal carrier 100 cos Znfat and a sinusoidal message with frequency fa-20 Hz, knowing that -0.7, a) Draw the single sided spectrum b) Determine the modulated signal bandwidth. c) Determine the 70% and 90% bandwidth and transınitted power.
Obtaining broadband FM signal from narrowband frequency modulated (FM) signal is shown below. The narrowband FM signal has a maximum frequency deviation of 100 Hz. The frequency of the local oscillator is f0=100 kHz. Obtaining broadband FM signal from narrowband frequency modulated (FM) signal is shown below. The narrowband FM signal has a maximum frequency deviation of 100 Hz. The frequency of the local oscillator is f0=100 kHz.Since the broadband FM signal has a carrier frequency of fc=80 MHz, find the N value.