An experiment was conducted using a communicating vessel to knowthehydraulic pressure. The communicating vessel consists of two column, XandY. Column X has a diameter of 15 cm and column Y of 75 cm. Oil (s = 0.852) wasfilled to the communicating vessel. A load of 1275 N was given to the columnY. Determine the minimum force that should be given to column Xso that theload can be lifted and the density of oil !

An experiment was conducted using a communicating vessel to knowthehydraulic pressure. The communicating vessel consists of two column, XandY. Column X has a diameter of 15 cm and column Y of 75 cm. Oil (s = 0.852) wasfilled to the communicating vessel. A load of 1275 N was given to the columnY. Determine the minimum force that should be given to column Xso that theload can be lifted and the density of oil !

Name: An experiment was conducted using a communicating vessel to knowthehyd
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: An experiment was conducted using a communicating vessel to knowthehydraulic pressure. The communicating vessel consists of two column, XandY. Column X has a diameter of 15 cm and column Y of 75 cm. Oil (s = 0.852) wasfilled to the communicating vess

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter8: Centroids And Distributed Loads

Section: Chapter Questions

Problem 8.121P: One side of the container has a 03-m square door that is hinged at its top edge. If the container is...

See similar textbooks

Similar questions

The 12-ft wide quarter-circular gate AB is hinged at A. Determine the contact force between the gate and the smooth surface at B due to water pressure acting on the gate. Use =62.4lb/ft3 for water.
The tank of an air compressor has a volume of 2m3 and is filled with air at a temperature of 40 degrees C. If agauge pressure on the tank reads 7.5 bars,what is themass of the air in the tank?
Engineers investigate the compressibility of fluid for the aircraft hydraulics. You are required to calculate the change in volume of 2litres of water if the pressure on the water is increased from 4 atmospheric pressure to 100atmospheres. Take the isothermal bulk modulus of water to be 2 x 20" atmospheres.
A 12.5 kg block of metal measuring 12.0 cm by 10.0 cm by 10.0 cm is suspended from a scale and immersed in 5.60 cm below the surface of the water. Scale a b (a) What are the magnitudes of the forces (in N) acting on the top and on the bottom of the block due to the s significant figures.) Frop N N Fbottom (b) What is the reading of the spring scale (in N)? N (c) Show that the buoyant force equals the difference between the forces at the top and bottom of the block. ( II
2. The tank shown contains alcohol (SG=D0.78) and covered by a circular plug 1.2 m in diameter. Calculate the hydrostatic force F Am acting on the plug and its center of pressure. 8m 1.2 m 3. The gate as shown is 3 m normal to the page. It keeps the two liquids from mixing with each onough clocuro botween the oil and
ASAP dont round off initial values, round off final ans only pls ty The pressure at a point in the seawater is 99 kPa, determine the pressure in kPa 48.13 meters below this point?
Q5 A U-tube manometer similar to that shown below is used to measure the gauge pressure of water (mass density p = 1000 kg /m3). If the density of mercury is 13.6 x 103 kg /m³, what will be the gauge pressure at A if h1 = 0.45 m and D is 0.7 m above BC. Wwater Wmercury
A closed cylindrical vessel, 2m in diameter & 4m high is fully filled with water & rotated to its vertical axis at a constant speed of 12.2 rad/sec. The top is pressurized by 180 KPa. (a) What is the pressure at the center bottom of the cylinder? (b) What is the pressure at the circumference bottom of the cylinder? (c) What is the total hydrostatic force at the sides of the cylinder?
Determine the pressure difference between points C and D. Take the specific weights to be Benzene: 8640 N/m?, Mercury:133100 N/m? Kerosene: 7885 N/m³, Water: 9790 N/m², Air: 12 N/m³. Water Benzene, Air D C 50 cm 19 cm 30 cm 18 cm 24 cm ст Mercury- Kerosine (answer) Pa
The pressure of the natural gas installation is as follows.As you can see, mercury (mercury), oil (oil) and water (water) fluidsIt is measured with a manometer. Open end of the manometer (X + 85)It is under the influence of kPa ambient pressure. The relative content of mercury and oil (relative to water)density (SG) and density of water (ρwater = 997 kg / m3) is known.Determine the absolute pressure in the installation (X=00)
A cylindrical disk ofwood weighing 45.0 N and having adiameter of 30.0 cm floats on a cylinderof oil of density 0.850 g /cm3(Fig.). The cylinder of oilis 75.0 cm deep and has a diameterthe same as that of the wood.(a) What is the gauge pressure at thetop of the oil column? (b) Supposenow that someone puts a weightof 83.0 N on top of the wood, butno oil seeps around the edge of thewood. What is the change in pressureat (i) the bottom of the oil and(ii) halfway down in the oil?
A multifluid container is connected to a U-tube, as shown in the figure. For the given specific gravitles and fluid column heights. determine the gage pressure at A. Also determine the height of a mercury column that would create the same pressure at A. The column heighth of oil is 86 cm. The specific gravitles are 1.26 for glycerin and 0.90 for oll. We take the standard density of water to be Pw=1000 kg/m³ and the specific gravity of mercury to be 13.6. h 35 cm 18 cm Į Oil SG-0.90 Water Glycerin SG-1.26 90 cm 15 cm The gage pressure at A is kPa. The height of a mercury column that would create the same pressure at A is cm.