An existing pipeline is to be reinforced with a new one whose coefficient of pipe friction is 2/3 of the old one. If the length of the new pipe is equal to that of the old one and the additional required capacity is 150% of the existing capacity. How big the new pipe should be compared to the old one. Use the Darcy - Weisbach formula. A 1.08 times 2.04 1.55 D 1.84

An existing pipeline is to be reinforced with a new one whose coefficient of pipe friction is 2/3 of the old one. If the length of the new pipe is equal to that of the old one and the additional required capacity is 150% of the existing capacity. How big the new pipe should be compared to the old one. Use the Darcy - Weisbach formula. A 1.08 times 2.04 1.55 D 1.84

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A pipeline of uniformly varying cross-section carries oil of specific gravity 0.87. The diameter of the pipe is 200 mm at end A and 500 mm at end B. The end B is located at 4 m higher than A. What is the loss of head in the pipeline if the pressure reading at A is 9.81 N/cm2 and at B is 5.886 N/cm²? (Take discharge is 200 litres/s and g = 9.81 m/s²)
The pipeline shown is having a diameter of 300mm, length is 5000m connecting reservoirs A and B as shown. To increase the capacity of the old pipeline due to increase in demand, a 300mmo pipeline 2500m long is laid out from the original pipeline at its midpoint towards reservoir B. Assuming f=0.02 for all pipes. 50m L = 5000m D=300mm p i.Determine the capacity of the old pipeline in m3/sec. a. 0.1725 c. 0.1342 b. 0.1213 d. 0.1534 ii.Determine the capacity of the new pipeline in m3/sec. c. 0.1534 a. 0.1725 b. 0.1213 d. 0.1342 iii.Compute the increase or decrease in flow from A to B. a. 0.0321 c. 0.0512 b. 0.0383 d. 0.0412
(a) Figure Q2.7 shows an inverted U-tube manometer with oil of density 800kg/m3 above thepipe liquid, which is water. The pipeline is horizontal. What is the value of (P1-P2)? (b) If the manometer readings are the same but the oil is replaced by air, what is (P1-P2) now? 280 mm Figure Q2.7 P₁ 北 P₂ 430 mm
Problem 4: Open Channel Flow A circular pipeline stretches 202 miles from an initial elevation of 510 ft to a final elevation of 230 ft. The pipe (D = 3.0 ft) is made of concrete (A=0.0030 ft). The open channel flow is steady and uniform such that the pipe is half full. The fluid is water at 50° F. Part A Sketch a cross-section of the pipe flowing half full, then calculate its hydraulic radius, Rh [ft]. Part B Calculate the discharge, Q [ft³/s].
Pipeline AB connects two reservoirs. The difference in elevation between the two reservoirs is 33 ft. the pipeline consists of an upstream section, D1= 30 in and L1 = 5000 ft and a downstream section, D2 = 21 in and L2 = 3500 ft. The pipes are concrete (f=0.016) and are connected end to end with a sudden reduction area. Compute the discharge capacity.
gle.com/u/0/c/MZE4MZY1MDM1NJ15/a/MzQ5Nzg10TcyOTM0/details jpg. Z, = ? Yol = 8.82 kN/m3 Z = 2. = 130 m 60 m- 7 m 130 m If oil flows from the upper to lower reservoir at a velocity 1.58 m/s in the 15 cm diameter smooth pipe, what is the elevation of the oil surface in the upper reservoir? Activat Go to Set
The two lines shown are the EGL and HGL of a pipeline. Which statement is true? A B D O There is a nozzle between Cand D The area of flow in AB is gradually decreasing There is turbine at C
Someone can help me with this one please?
Read the question carefully and give me right solution according to the question
QUESTION 5 A pipe system has a flow of 4.6 cfs. Section 1 has a diameter of 12" and Sectoin 2 has a diameter of 10". What is the velocity at each section? Section 1= 5.89 ft/sec Section 2= 9.2 ft/sec Section 1- 8.9 ft/sec Section 2= 6.0 ft/sec Section 1- 9.9 ft/sec Section 2= 9.9 ft/sec Section 1= 4.89 ft/sec Section 2= 6.58 ft/sec QUESTION 6 Click Save and Submit to save and submit. Click Save All Answers to save all answers. DELL Save All Answ
A pipeline with 30cm inside diameter is carrying a liquid at a flow rate of 0.025m^3/s.A reducer is placed in the line and the outlet diameter is 15cm.Determine the velocity at the beginning and end of the reducer. (Answer:v1=0.35m/s,v2=1.4m/s)
A decrease in flow area in a pipe .causes ........ in velocity Increase O Stop O Decrease O