An engineer's chain was used to measure a line, there were 6 tallies recorded, the rear chairman had 5 marking pins and the distance from the last pin to the end of line was 51.1 links. What was the length of the line?

Q: Explain grid leveling.

A: LevelingLeveling is the method or procedure to determine the relative altitude of any point on the…

Q: Define Bearings?

A: Bearing: It is defined as the angle which is measured between the reference meridian and the survey…

Q: Define earth work

A: The engineering work that is created by moving and/or processing unformed rock or large amounts of…

Q: A triangle has an area of 14 sq ft and a base of 7 feet. What is the height of thetriangle?

A: given data :  area of triangle (A) = 14 square feet  base (b) = 7 feet  height (h) = ?

Q: In detail what is the CSI MasterFormat and what is listed in division 28?

A: Answer  CSI MasterFormat also known as "Dewey Decimal system" is the product of the Construction…

Q: What are the characteristics of ordinal level measurement scale variables?

A: Data provided :  Ordinal level measurement scale variables    To determine : The characteristics of…

Q: Give a brief description: a. Measurement of Horizontal Distances b. Omitted Measurements c.…

A: Any plane which contains horizontal line and perpendicular  to the vertical direction is called as…

Q: Compute total indeterminacy

A: Given data : Number of external support reaction (R)=2+2+2=6 Number of member attach at hinge joint…

Q: Please fill in the blank for this question please! A *blank* call identifies a corner or boundary,…

A: A _________call identifies a corner or boundary, usually as some object that constitutes the…

Q: List the different meridians are used to specify directions?

A: The direction of a survey line can be defined in two ways: Relative to each other  Relative to some…

Q: Define Transform faults.

A: Transform fault is a kind of fault in which two tectonic plates slip past each other.

Q: What is PD 1594. Explain

A: Introduction:- PD 1594 (PRESIDENTIAL DECREE No. 1594) Prescribing polices, Guidelines, Rules and…

Q: In site design, what features matter the most?

A: This question is related to the Building design and construction from Civil Engineering. In this…

Q: Define the term Index Properties.

A: The index properties are the soil properties which help to identify and classify soil. These…

Q: Factors for planning include

A: before starting any project you need to do proper planning by using previous record , test…

Q: Explain the Eurocode terminology : GEO

A: GEO The application of scientific methods and engineering techniques and utilization of natural…

Q: geomorfologie

A: Note: As nothing is mentioned in this problem so, we are assuming that we have to only define this…

Q: What are the relationship of the Kings Road House (MAK Center)?

A: Kings road house is the name given to the house constructed on the west side of the Kings Road in…

Q: Define Foreshocks.

A: Foreshocks are earthquakes at the same location which precede larger earthquakes.

Q: What is the most important thing to ensure when it comes to layouting?

A: Civil surveying is a type of engineering that includes analysing and documenting information about a…

Q: what is the usual drawing paper size in preparing a lot plan ?

A: The drawing sizes for the construction plans will come in the different formats — with 18” x 24” and…

Q: What is the difference between interval and ratio level measurement scales?

A:

Q: What are the activities conducted by International Federation of Surveyors?

A: There are ten committees formed for conducting certain activities by FIG Committee 1- Practice for…

Q: actors that cause hardness along with a bibliography

A: The water hardness may be simply defined as the amount of dissolved calcium and magnesium in the…

Q: Describe about the Taylor Charts.

A: Taylor's stability chart are used for determining the stability of slope of cohesive homogeneous…

Q: Define International Federation of Surveyors

A: The International federation of surveyors is a non government organization recognized by United…

Q: a. On the equator: b. Golden, Colorado: C. Barrow, Alaska: 0° latitude 39°44'N latitude, 105°12'W…

A:

Q: hat exactly is meant when the term "scope" is used?

A: The term "scope" describes the total set of goals and demands necessary to finish a project.

Q: ow many square yards are there in a 72” x 112 yard roll?

A: GIVEN  WIDTH = 72"   = (72" )* (1'/12")*(1 yard/ 3') = 2 yard Length = 112 yard

Q: What is National Spatial Reference System?

A: National Spatial Reference System  (NSRS) A consistent coordinate system that defines latitude,…

Q: Define Spencer Charts.

A: Spencer defines the factor of safety as the available shear strength quotient divided by mobilized…

Q: Level surface, Bubble line, Horizontal line, Level line, Line of collimation, Bench mark, Change…

A:

Q: With the aid of an illustration, describe two methods by which areas bounded by irregular lines can…

A: Areas bounded  by irregular lines can be found by using midoridnate rule , trapezoidal method ,…

Q: Define SLS requirement

A: Solution: A Service level specification basically forms a part of the service level agreement in…

Q: What is a site plan? Discuss it. (M Please cite reference as per APA

A: A site plan is a detailed drawing that shows the area where the building has to be constructed…

Q: Define Aerial Photographs.

A: Aerial Photographs:

Q: Convert 36° 19' to decimal degree form.

A: Given data: θ=36∘19'

Q: Q#4: Define Baseline, Main survey line, check line and tie line?

A: - Baseline, main survey line, check line and tie lines are mostly used in triangulation surveying to…

Q: Figure below represent contour lines for ground surface and wells located on it 50 w2 W1 fill table…

A: given-water table elevation of wells-W1=60W2=50W3=40

Q: D#2: Write different uses of Surveying?

A:

Q: How to create border with title box in autocad 2024

A: Steps to create:Border with title box in autocad 2024.

Q: What are velocity charts?

A: The Velocity Chart displays the value amount delivered in each sprint so as to forecast the work…

Dependence on mechanical properties

The mechanical properties of materials are those structures that include the reaction to the load used. Metal switching features determine the scope of the usefulness of the content and establish the expected service life. Machine structures are also used to help distinguish and identify material objects. The most common mechanical properties considered are strength, ductility, stiffness, impact resistance, and resilience to fractures.