Answered: An elevator with mass of 200 kg rises… | bartleby

Related questions

Question

An elevator with mass of 200 kg rises with an acceleration of 1 m / sec^2. What is the tension in the supporting table?

Expert Solution

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Blurred answer

Similar questions

(a) Calculate the tension (in N) in a vertical strand of spiderweb if a spider of mass 8.00 x 10¯° kg hangs motionless on it. (Enter a number.) 0.000784 N (b) Calculate the tension (in N) in a horizontal strand of spiderweb if the same spider sits motionless in the middle of it much like the tightrope walker in the figure. 5.0° 5.0° T. TR w T. TR The strand sags at an angle of 15.0° below the horizontal. (Enter a number.) 0.046688914 X N Compare this with the tension in the vertical strand (find their ratio). (Enter a number.) (tension in horizontal strand) / (tension in vertical strand) =
An elevator weighing 22 000 N is supported by a steel cable. What is the tension in the cable when the elevator is being accelerated upward at a rate of 3.50 m/s^2? (g = 9.80 m/s^2) Choose answer here (N) 29857 N 27140 N 20000 N 26100 N
If you hang a car with a mass of 1770 kg from a steel beam, you observe that the beam bends 0.095 degrees. What is the tension in this beam, in newtons? Using the equation T=F/(2*sin(theta))
An elevator cab that weighs 23.2 kN moves upward. What is the tension in the cable if the cab's speed is (a) increasing at a rate of 1.02 m/s? and (b) decreasing at a rate of 1.02 m/s?? (a) Number i Units (b) Number i Units
Suppose you have a stack of 17 identical steel bars (steel bars have a mass of 1.00kg each). You are required to pull out bar number 16 from the stack (counting from the top of the stack down). Assuming that your assistant holds all other bars in place. If the coefficient of friction between steel and steel is 0.750, how hard do you have to pull (in N)?
An elevator (mass 4850 kg) is to be designed so that the maximum acceleration is 0.0680g. What are the maximum and minimum forces the motor should exert on the supporting cable?
An elevator weighing 20,000 N is supported by a steel cable. What is the tension in the cable when theelevator is being accelerated downward at a rate of 3.0 m/s2?
3. The force F required to move a box by pulling on an attached rope that forms an angle w with the horizontal is given by fmg F(w) = cOSw + f sin w where f, m, g > 0 are all constant. (a) Show that the angle wo that minimizes the required force to set the box in motion is given by arctan(f) (b) Show that this minimal force F(wo) is proportional to (a constant multiple of)
Consider a person standing on a scale in an elavator. If the elevator accelerates upwards with an acceleration of 1.21 m/s^2 and the person has a mass of 102.9 kg, what would the scale read?
2 3 40° M I B = 39.9°and M = 1.6 kg, what is the tension in string 1?
In the figure, a 799 kg construction bucket is suspended by a cable A that is attached at O to two other cables B and C, making angles 0₁ = 55.0° and 0₂ = 66.0° with the horizontal. Find the tensions in (a) cable A, (b) cable B, and (c) cable C. (Hint: To avoid solving two equations in two unknowns, position the axes as shown in the figure.) (a) Number i (b) Number (c) Number i Units Units Units B A C 09 >
Two blocks each of mass m = 3.90 kg are fastened to the top of an elevator as in the figure below. (a) If the elevator accelerates upward at 1.6 m/s?, find the tensions T, and T, in the upper and lower strings. N N T2 (b) If the strings can withstand a maximum tension of 99.0 N, what maximum acceleration can the elevator have before the first string breaks? m/s? 1.60 m/s m m

SEE MORE QUESTIONS