An electric heater is rated at 1750 W, a toaster at 500 W, and an electric grill at 1250 W. The three appliances are connected to a common 120 V household circuit. (a) How much current does each draw? A (heater) A (toaster) A (grill) (b) Is a circuit with a 28 A circuit breaker sufficient in this situation? ---Select--- Explain your answer.

An electric heater is rated at 1750 W, a toaster at 500 W, and an electric grill at 1250 W. The three appliances are connected to a common 120 V household circuit. (a) How much current does each draw? A (heater) A (toaster) A (grill) (b) Is a circuit with a 28 A circuit breaker sufficient in this situation? ---Select--- Explain your answer.

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

7 puan 4) A battery with unknown emf (e) and internal resistance (r) is connected to a circuit that involves an ideal voltmeter, a switch, and two resistors R1 =1 Q, R2 =10 Q, as shown below. When the switch is connected to a, the voltmeter reads 7 V. When the switch is connected to b, the voltmeter reads 10 V. Calculate the value of the internal resistance r. ET RI Rz 0.12 0 1.00 Q 0.25 0 0.50 0 O 0.75 0
Please answer
| C:/Users/tylrg/Downloads/Hw-7-Electric-circuits-II.pdf The diagram below shows a small water heater that uses electrical energy to heat water. The heating element is a small resistor labeled R1oad = 5.0 N immersed in the water. A 20 V ideal emf device supplies current and there is an adjustable resistor Ra in series. The value of the adjustable resistance can be changed to be anywhere between 1.0 - 3.0 N. The adjustable resistor is initially set to 2.0 Q and the switch is closed. (a) What is the voltage drop across the heating element? (b) How much energy is supplied by the source if the water heater runs for 10 minutes? (c) What fraction of this energy is actually used to heat the water? Please express your answer as a percentage, using only two significant figures. (d) Suppose the heating element degrades and corrodes and its resistivity slowly increases as the equip- ment becomes older. • Does the voltage drop across the heating element increase, decrease or remain the same as the…
1
Don't use chat gpt
10
A typical flashlight bulb is rated at 8 W. If the lightbulb drops 4.5 V, a) Draw a sketch of the circuit then b) Determine how much current goes through the lightbulb?
a) The standard household electrical circuits in your home are b) For the circuit shown below, R1 = 2.252, R2 = 50, R3 = 70, R4 = 80 and the battery voltage is 9V. R3 R4 R2 R1 V i) The equivalent resistance of the circuit is = ii) The source current is = A iii) The voltage drop across R2 is = V iv) The current through R3 is = A v) The power dissipated across R, is = W
1) For a circuit shown in Figure, (a) find the currents I,, I,, and I,. (b) find the potential difference between points a and b. (c) find the power on 8 N. 4Ω 7 V b a 3 V 8Ω 4Ω
When using an ammeter to measure current: Group of answer choices open the circuit at the positive and negative terminals of the battery. open the circuit and connect the meter in series between the two open ends. open the circuit at one point and connect the meter to one end. connect the meter across the battery or load.
Q.1) In the circuit shown below find i) Rar i) Ir, and the current in each resistor iii) The power absorbed in branch(BE) iv) Power dissipated in branch (CD) (25 mark) в 140 Ir t 22 V 14 22 n 10 n 28 1 E 18 2 D Q.2) Use source transformation technique to find the current flowing through the 22 resistor in the figure below. All resistor in ohm. (25 mark) 20A SA 28A
4) A battery with unknown emf (ɛ) and internal resistance (r) is connected to a circuit that involves an ideal voltmeter, a switch, and two resistors R1 =1 Q, R2 =10 Q, as shown below. When the switch is connected to a, the voltmeter reads 7 V. When the switch is connected to b, the voltmeter reads 10 V. Calculate the value of the internal resistance r. RI Rz 0.50 0 0.25 0 0.12 Q 1.00 0 0.75 Q Diğer: www