An eight-pole, 50 Hz, A-connected, synchronous generator with a fixed field current of 6 A was tested, and the following data were taken: Vroc Was measured to be 450 V. Isc was measured to be 364 A. When 8 V DC was applied to two of the terminals, 40 A DC was measured. When the armature current was 180 A, the internal (torque) angle was 25°. Find the values of: a) the armature resistance. b) the approximate synchronous reactance. c) the load power factor at IA = 180 A.

An eight-pole, 50 Hz, A-connected, synchronous generator with a fixed field current of 6 A was tested, and the following data were taken: Vroc Was measured to be 450 V. Isc was measured to be 364 A. When 8 V DC was applied to two of the terminals, 40 A DC was measured. When the armature current was 180 A, the internal (torque) angle was 25°. Find the values of: a) the armature resistance. b) the approximate synchronous reactance. c) the load power factor at IA = 180 A.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

23 kohm 18 kohm V. 4.8 V1 kohm 0.!2 kohm Please BE AWARE that there are multiple variable sheets Please use the variable sheet uploaded And calculate the cutoff frequency. Please give the answer in Hz and do not include anything else than the answer and the format will be in the scientific notation with 2 decimals (ex 5.01e+6 or 1.02e-4).
A 150 kW, 250-volt compound DC generator has its field windings which are connected in long shunt. If the shunt-field winding resistance is 20 ohms, what is the current in the series-field winding? (Note that the series field resistance is connected in series with the armature.)
An 8-pole lap wound d.e shunt generator has 120 slots with 4 conductors per slot. If each conductor can carry 250 A and flux per pole is 50 mWb. Find the speed so that it gives 240 V on open circuit. If terminal voltage of the generator drop to 220 on full load, find the armature resistance.
An 8-Pole, simplex lap wound, shunt generator has 800conductors and a flux per pole of 0.025Wb. The armature and shunt field resistances are 1ohms and 45ohms respectively. If a resistance of 11.25ohms is connected as load and the machine is running at 800rpm. Calculate the load current(in amp)
The armature winding resistance of a long shunt connected DC generator is 0.4ohm, the resistances of the shunt and serial field windings are 125 ohms and 0.1 ohms, respectively. While the generator supplies 8KW of power to the load it feeds, which is the voltage it produces since the output voltage is 250V?
I need the answer quickly
1)
The armature of a 14 pole DC shunt generator has 60 slots and is lap wound with 13 conductors per slots. The generator is running at a speed of 630 rpm and supplies a resistive load of 16 ohms at a terminal voltage of 310V. The armature resistance is 0.5 ohms and field resistance is 60 ohms. Find the armature current, the generated EMF and the flux per pole.
In a 4 pole DC shunt generator with a shunt field resistance of 100 ohms and an armature resistance of 1 ohm has 378 wave connected conductors in its armature. The flux per pole is 0.02 Wb. If a load resistance of 10 ohms is connected across the load terminals and the generator is driven at 1000 rpm, calculate the power absorbed by the load.
Solve it quickly please
An 8-Pole, simplex lap wound, shunt generator has 800conductors and a flux per pole of 0.025Wb. The armature and shunt field resistances are 1ohms and 45ohms respectively. If a resistance of 11.25ohms is connected as load and the machine is running at 800rpm. Calculate the terminal voltage (in Watts)
7) The flux per pole of a four-pole generator is 0.05 wb. It driven at a speed of 1500 rpm. In order to have an induced emf of 20 v per conductor, , if the winding is lap-connected, find (a) the number of conductors in series in each parallel path, (b) the number of conductors between brushes to generate 240 v, and (c) the total number of conductors in the armature.