An eight-pole, 24 KW, 124 V, DC machine has a duplex LAP-wound armature which has 72 coils with 6 turns per coil. Its rated speed is 3000 RPM. Ass ume no dead zone Find the constant K and the flux per poleto produce 80 Volts at no-load conditions Select one: O a. None O b. K = 68.86 and flux = 3.33 mwb/pole O c. K = 68.755 and flux = 3.7 mwb/ pole O d. K = 95.5 and flux = 3.7 mWb/ pole

An eight-pole, 24 KW, 124 V, DC machine has a duplex LAP-wound armature which has 72 coils with 6 turns per coil. Its rated speed is 3000 RPM. Ass ume no dead zone Find the constant K and the flux per poleto produce 80 Volts at no-load conditions Select one: O a. None O b. K = 68.86 and flux = 3.33 mwb/pole O c. K = 68.755 and flux = 3.7 mwb/ pole O d. K = 95.5 and flux = 3.7 mWb/ pole

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A 4-pole dc machine is wound duplex lap. Find the number of parallel path
Machine has 6 pole pairs and it is supplied with 50 Hz frequency. In order to double rated rotational speed, number of pole pairs in the design of the electrical machine must be changed to (put new number of pole pairs)
An eight-pole, 24 KW, 100 V, DC machine has a duplex LAP-wound armature which has 64 coils with 10 turns per coil. Its rated speed is 3000 RPM. Assume a dead zone of 4 coils that are always beyond poles faces. Find the constant K and the flux per pole to produce 80 Volts at no-load conditions Select one: O a. K = 59.5 and flux = 1.27 mWb/pole Ob. None Oc. K = 95.5 and flux = 2.67 mWb/ pole K = 91.5 and flux = 0.267 Wb/pole O d. i-0150
The voltage induced by a 6-pole DC generator running at 600 [RPM] with 100 slots on the armature and each armature coil has 4 turns with a flux per pole of 0.01 [Wb] is
The flux o in a 16 KW, 100 V, Duplex Lap-Wound DC machine has been set to induce rated voltage at a speed of 1500 RPM. Find the product Ko, and find the induced torque in this machine at rated load. Select one: O a. Product = 0.0667 , and Induced Torque = 10.667 N.m O b. None O c. Not enough information is given to find the torque O d. Product = 0.6366 , and Induced Torque = 101.86 N.m
Q- The armature resistance of a permanent magnet dc motor is 0.80. At no load, the motor draws 1.5 A from a supply voltage of 25 V and runs at 1500 rpm. The efficiency of the motor while it is operating on load at 1500 rpm drawing a current of 3.5 A from the same source will be
128. The hysteresis loss of a dc machine is 300 W when the flux per pole is 30 mWb and the machine is driven at 1000 rpm. How much Is the loss If the field is adjusted to produce 50 mWb per pole whlle the speed Is reduced to 900 rpm? A. 420 W B. 510 W C. 450 W D. 500 W
How voltage is built up in dc shunt generator
nid%3D11610 This course O d. Flux = 0.9 Wb, Speed = 473 rad/sec Clear my choice In a given DC motor, the output power is 20 HP, and the rotational losses are 1.1 KW. If the motor is operating at 87 % efficiency, find the converted power and the copper losses. Select one: O a. Peony =16 02 KW and Pa = 1.13 KW Ob. P.ry= 14.92 KW and P = 1.35 KW Oc None Od. Por= 1715 KW 3nd Pa-211kw Consider a shunt DC motor with an armature resistance RA -0.125 2 and terminal voltage VT =460V. TIhe motor rated speed is 1000RPM and the rated amature current is 100 A. The total field resistance is 260 Ohms
A direct current shunt dynamo continuously supplies an ohmic load of 50 Ohm at terminal voltage Vt= 1000 V. The armature winding resistance is 5 Ohm and the shunt pole winding resistance is 200 Ohm. The sum of mechanical losses is 400 W. What is the percent efficiency of the dynamo under these operating conditions? a) 70 b) 74 c) 87 d) 78 e) 85
Kindly solve what is ask with complete solution so that I can understand. I want a handwritten solution. Thank you very much pois!!
When the DC machine is running under saturation condition, then flux per pole decreases due to armature reaction. Select one: O True O False