An Egyptian pyramid has a square base and symmetrical sloping faces. The inclination of each sloping face is 53°07'. At a dis- tance of 600 ft from the base, on level ground, the angle of incli- nation to the apex is 27°09'. Find the vertical height and the slant height of the pyramid and the width of the pyramid at its base.

An Egyptian pyramid has a square base and symmetrical sloping faces. The inclination of each sloping face is 53°07'. At a dis- tance of 600 ft from the base, on level ground, the angle of incli- nation to the apex is 27°09'. Find the vertical height and the slant height of the pyramid and the width of the pyramid at its base.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: show full solution

A: Given data:The state of stress at a point is given by,To determine:The principal stresses, The…

Q: Which of the following is least likely to be found on a basic parts list? A. Find Number B. Quantity…

A: Find number refers to the ordering number that gives an ID tag to one of the parts in a parts list…

Q: How will the date code be applied to the assembly? 2. What paper size is the original version of…

A: Here given engineering drawing sheet shows the PRV Blank assembly drawing which consist of various…

Q: ldentify the engine parts in the drawing. Place the identifying letter next to the name of the part.

A: The naming of the engine part is as shown below,

Q: Given drawing of a Mechanical component, study the drawing carefully and then using Inventor, AUOB…

A: 1. Create the 3D Model of the part.

Q: 1- What type of drawing is this (Assembly, detail assembly, detail, pictorial)? And What is the…

A: Given Drafting To find Type of drawing Angle of projection Scale of drawing Original length of shaft…

Q: Pls use any CAD software to draw the sectional view of the solid attached in the image below.

A: FindWe need to draw the sectional view of the given object using CAD software.

Q: also why is Q/T0 being subtracted in sgen1 while other 2 its being added

Q: Files are used for removing large of amount of materials. Select one: True False

Q: Piping isometric is produced:

A: This question is based on the concept of the piping isometric.

Q: 5 ft 2 ft 7 ft The train has a weight of 23000 Ib and a center of gravity at G. It is suspended from…

A: Free Body Diagram for the given condition can be made as shown below: All normal reactions are…

Q: I need these 3 parts answered for a review activity.

A: A detailed drawing is a two-dimensional representation of the layout of the engineer that contains…

Q: 1. Draw a FBD for the cylindrical tub before the metal object is added, clearly labeling all forces.…

A: When a body is immersed in water , the following forces acts on the body 1) Weight of the body 2)…

Q: What is the lowest allowable dimension for the flats?

A: Solution:

Q: Design the solid model shown. There should only be 4 sketches max and an applied feature. This…

A: according to the given details in the question.

Question

Please show all work and how you did it with proper units and Full body diagram if needed. Thanks

1.19 An Egyptian pyramid has a square base and symmetrical sloping
faces. The inclination of each sloping face is 53°07'. At a dis-
tance of 600 ft from the base, on level ground, the angle of incli-
nation to the apex is 27°09'. Find the vertical height and the slant
height of the pyramid and the width of the pyramid at its base.
53° 07'
27° 09'
600'
PROBLEM 1.19

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Subparts 1, 2, and 3.
What does the shear flow measure?
Using autocad draw necessary views. Kindly all the views I'll rate your solution
This was not correct may you please
The denomination for a force or shrink fit in the US system is ?
If the answer is no can anything be done to save the part?
Tire manufacturers recommend that you check your tire pressure monthly to avoid unnecessary tire wear and enhance safety. This is best done when the tires are cold meaning; the car has not been driven for at least 2 hours. Since you leave for work before the sun comes up you decide to inflate your tires to the recommended pressure right after you get home from work in the afternoon when the tires are still warm. What would you find if you rechecked your tire pressure after the tires have cooled down? A.Tire pressure has decreased because there is a decrease in kinetic energy of themolecules resulting in more collisions with the inside walls of the tire thusincreasing the pressure inside the tire. B.Tire pressure has increased because there is a decrease in kinetic energy of the molecules resulting in fewer collisions with the inside walls of the tire thus decreasing the pressure inside the tire. C.Tire pressure has increased because there is an increase in kinetic energy of the…
Diagram: Given the hook-up drawing, list all the equipment, tools and materials that are needed in installation. INST. PIPING 1- *1 INST. PIPING
Hello, Can someone help me with this worksheet please?
Paula has worked for Brindle Corporation for 3 years. During this time, she has worked as a machine operator/cell leader in various work cells. Recently, the plant went to mandatory 12-hour shifts and plans to remain on this schedule for several months. Paula’s present work cell is manufacturing 3-inch diameter exhaust tubes that are made from stainless steel. These tubes get a hole punched in them, a flange welded on, and burrs ground off. The pipe then gets placed into a gage to check that it was made correctly. (The tubes weigh about six pounds.) Paula has been performing the welding operation. She leans into the machine and loads the part into a fixture then positions the flange. Both pieces are clamped (using hand clamps) into position and the machine is cycled by depressing two palm buttons. The gaging operation requires placing the finished part into the gage and clamping it (using hand clamps) into place. A pin is depressed to verify the position of the hole and a…
Paula has worked for Brindle Corporation for 3 years. During this time, she has worked as a machine operator/cell leader in various work cells. Recently, the plant went to mandatory 12-hour shifts and plans to remain on this schedule for several months. Paula’s present work cell is manufacturing 3-inch diameter exhaust tubes that are made from stainless steel. These tubes get a hole punched in them, a flange welded on, and burrs ground off. The pipe then gets placed into a gage to check that it was made correctly. (The tubes weigh about six pounds.) Paula has been performing the welding operation. She leans into the machine and loads the part into a fixture then positions the flange. Both pieces are clamped (using hand clamps) into position and the machine is cycled by depressing two palm buttons. The gaging operation requires placing the finished part into the gage and clamping it (using hand clamps) into place. A pin is depressed to verify the position of the hole and a…