An eccentrically compressed column is of rectangular section. The dimensionsof the column are b x h = 500 mm × 800 mm, a̟ = a,6 = 12.5 m. The strength of the concrete is fe = 14.3 N/mm². The properties ofthe reinforcement are f! = fy = 300 N/mm² and E, = 2 × 10° N/mm?. If theaxial force N. = 1800 kN and the moment M = 1080 kN-m are applied on themember and the section is asymmetrically reinforced, determine A, and A.%3D40 mm, and

The combination of steel and concrete that resists forces together is reinforced concrete. Rods,…

An eccentrically compressed column is of rectangular section. The dimensions of the column are b x h = 500 mm × 800 mm, a, = a, 6 = 12.5 m. The strength of the concrete is f. = 14.3 N/mm². The properties of the reinforcement are f = f, = 300 N/mm² and E, = 2 x 10° N/mm?. If the %3D = 40 mm, and %3D %3D %3D %3D axial force N. = 1800 kN and the moment M = 1080 KN•M are applied on the member and the section is asymmetrically reinforced, determine A, and A.

An eccentrically compressed column is of rectangular section. The dimensions of the column are b x h = 500 mm × 800 mm, a, = a, 6 = 12.5 m. The strength of the concrete is f. = 14.3 N/mm². The properties of the reinforcement are f = f, = 300 N/mm² and E, = 2 x 10° N/mm?. If the %3D = 40 mm, and %3D %3D %3D %3D axial force N. = 1800 kN and the moment M = 1080 KN•M are applied on the member and the section is asymmetrically reinforced, determine A, and A.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

9. If the value of the fc' of concrete is 30 MPa, and the actual stress of the concrete subjected to a force is 12 MPa, at what stage is the concrete at?
Design Problem 1 & 2 Determine the cracking moment for the prestressed beam section shown if f'c = 35 MPa. Use a modular rupture of fr Assume normal weight concrete. = 0.621√ f'c C = 100 mm b₁ = 350 mm D = 125 mm d = 440 mm h = 500mm b₂ = 200 mm Figure 1.0 Cc 60 mm C-150 mm h, 250 mm b₁ = 250 mm b. =350 mm Figure 2.0 d 630 mm h = 700mm Ce 70 mm
A group of concrete cubes mixed with different water ratios .. The group with water ratio W / c = 0.3The maximum load was testedFailure causes every cube in the group Required:1- Finding the stress rate for each group in unit N / mm2 with discussing the results and the effect of the water w / c ratio on the compressive strength of the group.
Please give me the correct solutions and answer of this problem in principles of reinforced/prestressed concrete
A half-block concrete masonry unit is subjected to compression until failure.The outside dimensions of the specimen are 190 mm X 190 mm X 190 mm.The cross section is a hollow square with a wall thickness of 38 mm. The loadis applied perpendicular to the hollow cross section and the maximum loadis 296 kN.a. Determine the gross area compressive strength.b. Determine the net area compressive strength.
Subject: Reinforced Concrete Structures exam
A rectangular beam has the following properties. Assume 12 mm stirrups. Assume a single layer of reinforcements. Calculate Mu. Given: Width of the beam, = 300 mm Over-all depth, h = 425 mm Tension reinforcements = 5 pcs 28 mm dia Comp reinforcements = 4 pcs 20 mm dia Specified strength of concrete, f'c = 28 Мра Steel yield strength, fy = 345 MPа Note: Round off your final answer in 3 decimal places. No need to type the units.
Given Data: Concrete dimensions Area of steel 625 560 f = 30 MPa ЗHD25 f, = 420 MPa A, = 2457 mm² 65 %3D b = 250 Required: What is the maximum uniformly distributed live load it can support in addition to dead load?
A simply supported beam 6.5m long, 350mmx500mm, prestressed with a straight tendon located 150mm below the neutral axis with effective prestressing force, Pe, of 300kN. Total load carried by the beam is 20kN/m. A. Determine the area of the concrete, mm2.B. Determine the section modulus of the concrete in x10^3 mm^3C. Determine the compressive stress caused by the tendon alone if Pe is at the centroid, MPa
Find the minimum theoretical width and height of a rectangular concrete section that will make the beam failure sufficiently ductile. Given: Two layers of 2-Ø25 mm bottom reinforcements fy=414 MPa f'c=35 MPa stirrup diameter=minimum required clear cover=minimum value for beam vertical clear spacing bet. Iayers=minimum value for beam height-to-width ratio=2.0 Note: Ductile failure occurs in beams when the extreme reinforcement layer is strained to 0.004 or greater.
Determine the values of the distance cfrom the extreme concrete corppression fibers to the neutral axis, andr, for the beam shown in the following Figure fy 60,000 psi and fc 3000 psi. 0.003 21 in d-c 389 bars 3.00 in) = (0.003) 12 in Select one: a. 6.90 in, 0.0061 b. 6.25 in, 0.0069 c. 7.50 in, 0.0085 d.5.93 in, 0.0076
please answer in the nearest 3 decimal numbers