An E-Shape beam with the cross-section is bent about vertical axis. As shown in Figure Q3, N-N is plastic neutral axis Assume that the yield stress, oy is 275 MPa and the elastic bending moment, My is 18.88 kNm, (i) determine the plastic moment, Mp of the beam. (ii) determine the value of the shape factor for the beam. N 20 тm |20 тm 100 тm 20 тm 60 тm 20 mm 80 тm Figure Q3

An E-Shape beam with the cross-section is bent about vertical axis. As shown in Figure Q3, N-N is plastic neutral axis Assume that the yield stress, oy is 275 MPa and the elastic bending moment, My is 18.88 kNm, (i) determine the plastic moment, Mp of the beam. (ii) determine the value of the shape factor for the beam. N 20 тm |20 тm 100 тm 20 тm 60 тm 20 mm 80 тm Figure Q3

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

HELP ME!
4
The beam shown in Fig QB1 is made from aluminium tube of rectangular cross-section having a vertical height of 50mm, a horizontal width of 30mm and a wall thickness of 3mm. The dimensions given in the figure are in millimetres. The yield stress in tension is 200MPa; Young's modulus is 71GPa. Determine: an expression for the bending moment at every point in the beam and draw the bending moment diagram a) b) c) d) the maximum bending moment the maximum longitudinal stress the maximum vertical deflection 200 3kN 200 1kN 100
30. An aluminum alloy rod has a circular cross section with a diameter of 8mm. The rod is subjected to a tensile load of 5kN. Assume that the material is in the elastic region and E = 69 GPa. If Poisson's Ratio is 0.33, what will be the lateral strain? E= 6/8 v = -E(lateral)/(axial)
A small aluminum alloy [E = 71 GPa] tee shape is used as a simply supported beam as shown. For this beam, a = 120 mm. The cross- sectional dimensions of the tee shape are b = 17 mm, d = 26 mm, andt = 6 mm. After loads are applied to the beam at B, C, and D, a compressive normal strain of 460 µɛ is measured from a strain gage located at c = 10 mm below the topmost edge of the tee stem at section 1-1. What is the applied load P? P P ЗР Strain gage C |D H Answer: P = N
A bar made from aluminum (E = 72 GPa) has a diameter of 12 mm. When the bar is subjected to a tensile axial force P, its diameter is decreased by 0.018 mm. Assume the Poisson’s ratio to be 0.33. Determine the value of loads P and its axial deformation. P = ? N δ = ? mm
Find the req,
A rod is composed of an aluminum section rigidly attached between steel and bronze sections, as shown in the figure. Axial loads are applied at the positions indicated. If P 4000 Ib and the cross-sectional area of the rod is 1.0 sq.in. What is %3D the stress in the bronze? (in ksi) Note: indicate sign (no sign means positive/tenslon) 4P Steel Bronze Aluminum 2 ft 3 ft 2.5 ft
8. A rigid bar AB is supported by three rods. A load P = 250 kN is applied to the bar. The modulus of elasticity of copper is 110 x 10°6 kN/m^2 and modulus of elasticity of steel is 200 x 10°6 kN/m^2. Steel rod A= 900 sq. mm Steel rod A= 900 2m sq. mm Copper A=1200 sq. mm 2m B 1m 1m Determine the deformation in the rods (in mm). * Your answer
Problem # 8: A bar made from aluminum (E = 72 GPa) has a diameter of 12 mm. When the bar is subjected to a tensile axial force P, its diameter is decreased by 0.018 mm. Assume the Poisson's ratio to be 0.33. Determine the value of loads P and its axial deformation. d = 12 mm P L 1.20 m P
The rectangular steel plate in the figure is forced by the forces given at the A and B points. a) Size the cross section according to the most economical section ratio a / b = 1/2. b) Calculate the amount of deformation occurring in the rod in this case. The yield stress of the steel plate can be taken as 400 Mpa, the modulus of elasticity 2.10 ^ 5 Mpa, the safety coefficient of the design can be taken as 2. F = 3kN L = 1.5m
1. The column in the figure shown has a strain on its compressive edge equal to -0.003 and has a tensile strain of +0.00185 on its other edge. Detemine the nominal values of Pn and Mn that cause this strain distribution if f'c = 21 MPa, fy = 414 MPa. Draw the column interaction diagram. en 600 Pn mm 8 - 6 32mm 75 225 225 75 600