An axial load P is applied to a 220"-long bar with stepped cross-section as shown in Fig. 1. The area of each cross-section is shown in the figure. The stress-strain relation for the material used can be expressed as follows: 20,000€ 1+ 400€ 0 = 0 ≤ ≤ 0.03 (0 = ksi) in which the strain & is nondimensional and o has units of kips per square inch (ksi). You may assume that the elastic modulus is the same for the entire bar and is equal to the slope of the stress- strain curve at the origin. Determine the axial elongation (in inch) and strain (in %) of the bar if P = 30 kips A₁ = 5 in² A-15 in2

An axial load P is applied to a 220"-long bar with stepped cross-section as shown in Fig. 1. The area of each cross-section is shown in the figure. The stress-strain relation for the material used can be expressed as follows: 20,000€ 1+ 400€ 0 = 0 ≤ ≤ 0.03 (0 = ksi) in which the strain & is nondimensional and o has units of kips per square inch (ksi). You may assume that the elastic modulus is the same for the entire bar and is equal to the slope of the stress- strain curve at the origin. Determine the axial elongation (in inch) and strain (in %) of the bar if P = 30 kips A₁ = 5 in² A-15 in2

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A small aluminum alloy [E = 71 GPa] tee shape is used as a simply supported beam as shown. For this beam, a = 120 mm. The cross-sectional dimensions of the tee shape are b = 17 mm, d = 26 mm, and t = 6 mm. After loads are applied to the beam at B, C, and D, a compressive normal strain of 460 με is measured from a strain gage located at c = 10 mm below the topmost edge of the tee stem at section 1-1. What is the applied load P?
A strain rosette was attached to the outer surface of stainless vessel when the vessel is in a stress-free state. The vessel was then put under a complex loading (pressure, bending and torsion) state. The train readings for the three strain gage elements in the strain rosette were recorded as: Ea=210, Eb=160, Ec-330, all in micro-strains. The mechanical properties of the stainless material are known: E=193 GPa, G=76 GPa, v=0.27, oy=205 MPa. Calculate the following: 1. Principal strains and in-plane maximum shear strain. 2. Principal stresses and absolute maximum shear stress. 3. The factor-of-safety based on the maximum shear stress failure theory. 4. The factor-of-safety based on the maximum distortion energy failure theory. 45° 45° b 45° strain rosette X
The stress-strain diagram for polyethylene, which is used to sheath coaxial cables, is determined from testing a specimen that has a gage length of 11 in. A load P on the specimen develops a strain of € = 0.024 in. /in. (Figure 1) Figure σ (ksi) 5 4 3 2 1 O = 3,7 e O 0.008 0.016 0.024 0.032 0.040 0.048 0.004 1 of 1 P € (in./in.) Part A Determine the approximate length of the specimen, measured between the gage points, when the load is removed. Assume the specimen recovers elastically. Express your answer in inches to four significant figures. 15] ΑΣΦ | 11 | vec L = Submit Provide Feedback Request Answer www ? Review in. Next >
A tube has 25mm outside diameter and an axial tensile load of 40 kN. If the strain on the tube is limited to 0.1% and density of 7800kg/m^3, what is the maximum internal diameter of the tube in mm?
Please show each and every step in detail. Dont miss any steps and highlight the final answer. Thanks!
1
A steel thick cylinder of external diameter 150 mm has two strain gauges fixed externally, one along the longitudinal axis and the other at right angles to read the hoop strain. The cylinder is subjected to an internal pressure of 75 MPa and this causes the following strains: (a) hoop gauge: 455 x 106 mm/mm tensile; (b) longitudinal gauge: 124 x 10 mm/mm tensile. Find the internal diameter of the cylinder assuming that Young's modulus for steel is 208 GPa and Poisson's ratio is 0.283.
1-A round member having a diameter of 3cm experience an axial load of 10KN. Two strain gauges are mounted on the member, one measuring an axial strain of 600 micro-strain and the other measuring a lateral strain of -163 micro-strain. The modulus of elasticity in GPa is Choose... The Poisson ratio is Choose... + The stress in MPa is Choose... + Next page
Q1/ The bar shown in Fig. 1 is subjected to a tensile load of 50 KN. Find the diameter of the middle portion if the 'stress is limited to 130 MN/m². Find also the length of the middle portion if the total elongation of the bar is 0.15 mm. Take E=200 GN/m². 50 kN Fig. 1 40 mm dia. + P x 250 mm 40 mm dia 50 kN
An aluminum alloy [E = 70 GPa; v = 0.33; a = 23.0x10-6/°C] bar is subjected to a tensile load P. The bar has a depth of d = 270 mm, a cross-sectional area of A = 13520 mm², and a length of L = 4.5 m. The initial longitudinal normal strain in the bar is zero. After load P is applied and the temperature of the bar has been increased by AT = 46°C, the longitudinal normal strain is found to be 1830 με. Calculate the change in bar depth d after the load P has been applied and the temperature has been increased. P Answer: Δd = i d eTextbook and Media Save for Later L mm Attempts: 0 of 5 used Submit Answer
A rigid steel bar is supported by three rods as shown. There is no strain in the rods before the load P is applied. After load P is applied, the normal strain in rods (1) is 2410 µm/m. Assume initial rod lengths of L₁ = 1,250 mm and L₂ = 2,000 mm. Determine the normal strain in rod (2). (1) 4₁ (2) Rigid bar O 975 μm/m O 1072 μm/m O 1757 µm/m O 1656 µm/m O 1506 μm/m B P L₂ (1)
Please answer in proper units